ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be
implemented for installation and start-up. Therefore, the installer as well as the user must read the instructions before
beginning installation and start-up.
Keep this manual for future reference.
To achieve optimum performance of the Mini light for LED's, follow the instructions provided below:
1. VERIFY THE CONTENTS OF THE PACKING:
The following accessories are included inside the box:
Mini light (35931 / 36652)
Unit Floodlamp
Decorative key
O'ring
2. GENERAL CHARACTERISTICS:
This floodlamp has been designed to be used fully submerged underwater in fresh water SPAS. It is a Class III electric
apparatus with very low safety voltage (12 V with alternating current).
The floodlamp complies with IPX8 degree of protection (resistance to penetration of dust, solid bodies and humidity) at a
nominal immersion depth of 2 m.
This floodlamp complies with international safety standards for lights, especially the EN 60598-2-18 standard: LIGHTS
PART 2: SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric components
which have been inserted or handled at locations other than its own premises.
3. INSTALLATION:
• In order to clearly light a pool it is recommended to install a floodlamp every 5 m
which are especially deep, a floodlamp is required for every 10 m
• In order to prevent glare, the floodlamps should be installed so that they face away from the residence or usual view of
the swimming pool.
• In the event that lighting is used in training or competition pools, the floodlamps should be installed on the sides to
prevent glare on the swimmers.
• To avoid the need to empty the pool to change the lamp, we recommend that the floodlamp be installed in areas which
are accessible from the upper edge of the pool.
Prior to installation verify that the gland seal has been fully tightened.
4. ASSEMBLY:
Mini light 35931 / 36652
This light is manufactured for installation in guiding tube.
1. Install the wall conduit in the concrete wall, at a distance of 400-700 mm. below the water level (Fig. 1).
2. The wall conduit must be extended with a cable conduit the length of which remains above the maximum level of the
swimming pool or spa (Fig. 2).
3. Feed the light cable through the conduit (Fig. 3).
4. Then fit the light itself, pushing it into place (Fig. 4).
Mini light 35932 / 36654
This light is manufactured for installation in SPAS and metal or polyester bath-tubs. It does not require a niche or guiding
tube for its installation.
1. the light should be installed at approximately 400 mm below the water-level of the SPAS and in a place where it can not
easily be covered by the body of a person. Install it preferably in the wall of the steps at the entrance of the SPAS (Fig.1).
2. With the use of a drill make a round hole a diameter of 60 mm in the wall of SPAS (Fig. 5).
3. Place the rubber gasket and the light inside the SPAS.
4. Place the nut of 2" on the back-part of the body of the SAPS. Fixing the nut to the body of the light (Fig. 6).
Attention:
• In order to ensure full watertightness clean the seat of glass butt joint or replace this if any permanent deformation or
notches are visible.
• Firmly tighten the gland seal nut.
• Always install the body in order an easy manipulation from the outside, or in one way that you can extract it out without
many difficulties.
• Before any handling ensure that there is NO voltage supplied to the floodlamp.
Take the precaution of leaving 1.5 m of cable wound on the body of the floodlamp in order to be able to remove the
floodlamp to the edge of the pool in the event that handling is required (Fig. 7).
Mini light (35932 / 36654)
Unit floodlamp
Decorative key
Butt joint
Nut
3
of water volume.
2
2
of water surface. In swimming pools