Intended Use; Technical Data; Before Starting The Equipment; Assembling The Equipment - EINHELL TC-VC 18/20 Li S Traduction Du Mode D'emploi D'origine

3. Intended use

The cordless wet/dry vacuum is designed for wet
and dry vacuuming using the appropriate fi lter.
The equipment is not suitable for the vacuuming
of combustible, explosive or harmful substances.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ............................18 V
Air fl ow: ................................ 53 cfm (1.5 m³/min)
Vacuum pressure max.: .............................. 8 kPa
Vacuum hose length: ....................... 4.9 ft (1.5 m)
Tank capacity: .................................4.8 gal (18 l )
Weight: ......................................... 7.9 lbs (3.6 kg)

5. Before starting the equipment

5.1 Assembling the equipment

Fitting the head (Fig. 1,3,4)
The equipment head (3) is fastened to the
tank (7) by the locking hook (6). To remove the
equipment head (3), open the locking hook (6)
and take off the equipment head (3). When fi tting
the equipment head (3), make sure that the
locking hook (6) locks into place correctly.
Fitting the castors (Fig. 5)
Fit the castors (13) into the appropriate mountings
on the underside of the tank (7).
5.2 Fitting the fi lters
Important!
Never use the wet/dry vacuum without a fi lter.
Always ensure that the fi lters are securely seated.
Fitting the foam fi lter (Fig. 6/Item 15)
For wet-vacuuming, slip the supplied foamed
plastic fi lter (15) over the fi lter basket (Figs. 3/4).
Anl_TC_VC_18_20_Li_S_USA_SPK7.indb 9 Anl_TC_VC_18_20_Li_S_USA_SPK7.indb 9
EN
Fitting the pleated fi lter (Fig. 7)
For dry-vacuuming, slip the pleated fi lter (Fig. 18)
onto the fi lter basket (Fig. 3/Item 4). The pleated
fi lter is suitable for dry-vacuuming only.
Fitting the dirt bag (Fig. 9/Item 14)
For vacuuming fi ne, dry dirt it is recommended
that you fi t the dirt bag (Fig. 2/Item 14). Slip the
dirt bag (14) over the vacuuming hole. The dirt
bag (14) is suitable for dry-vacuuming only. The
dirt bag makes it easier to dispose of the sucked-
in dust.
5.3 Fitting the suction hose (Fig. 3, 10, 11)
Connect the suction hose (10) to the
corresponding connector on the wet/dry vacuum,
depending on the application required.
Vacuuming
Connect the suction hose (10) to the suction hose
connector (8).
Blowing
Connect the suction hose (10) to the blow
connector (9).
To extend the suction hose (10) you can attach
one or more of the elements which make up the
3-part suction tube (11) to the suction hose (10).
The adapter (17) must be inserted between the
suction tube (11) and the combination nozzle (12)
or crevice nozzle (16).

5.4 Suction nozzles

Combination nozzle (Fig. 2)
The dual-purpose nozzle (12) is for vacuuming
solids and liquids over medium to large areas.
Crevice nozzle (Fig. 2)
The crevice nozzle (16) is designed for
vacuuming solids and liquids in corners, edges
and other areas that are diffi cult to access.
Upholstery nozzle (Fig. 2)
The upholstery nozzle (22) is specially designed
for vacuuming solids on upholstery and carpets.
Fitting the tool adapter
You can use the supplied tool adapter (Fig. 2/
Item 24) to connect the suction hose (10) to the
tool. To do so, fi t it between the suction hose
and the extractor port on the tool. Check that the
connections are secure and air-tight.
- 9 -
16.04.2019 12:48:23 16.04.2019 12:48:23