Bluetooth Operation - Trevi TT 1020 BT Mode D'emploi Et Branchement

ENGLISH
POWER SUPPLY AND BATTERY CHARGE
This device uses a rechargeable lithium battery. Upon completion of the charge it will work without being connected to a power outlet.
Recharge the battery only with player off and indoors.
- Connect the device to the mains adapter and insert the latter into a mains socket.
- The charge indicator (16) lights: flashing red indicates battery charging, fix red indicates battery charged.
The charging time with unit switched off (fast charge) is about 5h.
Low battery: when the battery is low, the device emits a BEEP sound and then goes off automatically.
Caution: for recharging the battery only use the power supply provided with the appliance.
WARNING FOR PROPER USE OF THE RECHARGEABLE BATTERIES
Recharge the batteries at a temperature comprised between 5 ° C and 35 ° C.
Do not prolong the charging over the indicated time period to avoid the risk of overheating and bursting
The battery charging over the indicated time period or a prolonged period of inactivity may shorten its life.
The rechargeable battery is subject to wear and its capacity gradually decreases.
ON / OFF / VOLUME
1. To turn the unit rotate the volume knob (18) clockwise (you will hear a click).
2. To switch off the appliance rotate the volume knob (18) counter-clockwise until it stops (you will hear a click).
3. Adjust the volume using the volume knob (18).
- After a certain time of inactivity, the device will enter Standby mode, to reactivate the device turn off and on using the volume knob (18) as described.

BLUETOOTH OPERATION

1. Set the selector switch (25) on the position of USB / BT; remove, if present, Usb memory from the USB socket(14).
2. In Bluetooth mode, the system automatically goes into research.
3. Activate the Bluetooth functionality on the external device to be coupled and make it visible.
4. Initiate a search for devices. At the end match the "TreviTT1020BT" device.
5. Press the PLAY / PAUSE button (23) to start playback.
6. Press the NEXT button (22) while listening to switch to the next track.
7. Press the PREV button (21) during playback to go to the previous track.
8. Press the PLAY / PAUSE button (23) to pause, press again to resume play
NOTE: in case the BT connection is interrupted repeat the pairing procedure as described.
OPERATION USB PLAYER
1. Insert a USB device in the entrance (14).
2. Turn the selector switch (25) on the USB / BT position, playing tracks start automatically.
3. Press the PLAY / PAUSE button (23) to pause, press it again to resume play.
4. Press and hold the STOP button (24) on the unit to stop playback.
5. Press the NEXT button (22) during playback to go to the next track, long press to fast forward on listening to the song.
6. Press the PREV button (21) during playback to go to the previous track, long press to quickly scroll back listening to the track being played.
- The player may not support some USB devices, this is due to the incompatibility of some processors.
TURNTABLE
1. Turn the selector switch (25) on the PHONO position.
2. Select the correct drive speed (33/45/78 rpm) through the selector speed turntable (7).
3. Place the disk on the plate. Use the supplied adapter (1) if the disc is a 45.
4. Release the arm from the locking hook (8); raise the arm and position the stylus on the disc, operate the lever (3) to lower the head support arm.
NOTES:
- Remove the cartridge protection before use.
- Ensure that the arm is blocked from the loocking hook before and after use, before operating the lock hook make sure you have lowered the head
support arm via the lever (3).
- Some discs may be interrupted before the end, since the area of the disc does not coincide with the settings of this unit. In this case, position the
selector AUTO STOP (4) to OFF. In this way, the disc will play to the end, but it will not stop automatically.
AUX IN
1. Set the selector switch (25) to the AUX IN.
2. Connect any unit having audio output through a special cable Jack 3.5mm (not included) to the AUX IN (11).
3. Operate the external unit by its own commands.
MP3 ENCODING FROM TURNTABLE/AUX IN
This device allows the recording of audio tracks from the turntable and input Aux In in USB device in MP3 format.
ENCODING FROM RECORD PLAYER / AUX IN
1. Turn on the appliance and select the Phono function or the function Aux In. If you use the Aux In insert the audio cable (not supplied) with the
external source.
2. Insert an USB memory in Usb input(14).
3. Press the Auto / Manual (19) key to select the preferred recording type:
7
TT 1020 BT