Battery Replacement - CABASSE SANTORIN 38 Notice D'installation

f. « Start Acq. 3 ? »:
f1. Place the microphone around 60 cm away from (P1)
position, opposite side of (P2) , somehow in front of
ENGLISH (P2) and around 60 cm above initial position (P3).
f2. Press « ENTER » to launch the measurements acqui-
sition 3.
g. «Finished!»: the automatic room compensation is achie-
ved . Validate the recording for the selected PRESET with
"OK". It is then possible to record other compensations
in another PRESET with other microphone positions.
Before starting listening tests: Select « XLR» as
« SOURCE » if necessary and unplug the mi-
crophone
Check and if necessary set the "VOLUME" of the
subwoofer, as the EQprocess might have modified
the sound level around the low-pass frequency.
Unplug and store carefully the measurement equip-
ment for eventual further use after having completed
the set-up of the subwoofer.
G2) MANUAL ROOM EQUALISATION:
This way of setting up might bring better results than the Cabasse
autocalibration system only if skilled people with specific mea-
surement equipment are involved. It can also be used to slightly
modify some auto-calibration values for audio comparisons of dif-
ferent PRESETS ((RC6) keys) or use of sources with different sound
balances.
1) Select PRESET ( 1, 2 or 3).
2) Use the «  » and «  » keys (TP6 et TP3) of the control pad ,
then « ENTER »to select one of the parametric modules:
PARAMETRIC 1, PARAMETRIC 2, PARAMETRIC 3.
3) « CENTER »: choose the middle frequency of the bandwidth
to be modified, between 30 and 200 Hz in 1 Hz increments.
4) « BAND »: select the width of the correction, from 1/8 of an
octave up to 2 (16/8) octaves in 1/8 of an octave increments.
5) GAIN: adjust intensity of the correction, adjustable from -12
dB to +4 dB in 1 dB increments.
6) Validate the above 3 values: press the ENTER key (P1) on
« EXIT ».
7) Proceed the same way for the other parametric modules if
they are to be used.
16
SANTORIN 38 - SUBWOOFER OPERATING INSTRUCTIONS
preamplifier from the subwoofer.
H) USE OF PRESET1,PRESET2,PRESET3:
The factory setup is with PRESET 1 on. The gains of the 3 parame-
tric modules are set on 0 dB, bandwidth being on 1 Octave. The
frequencies are preset on 50 Hz for PARA 1, 60 Hz for PARA 2, 70
Hz for PARA 3.
1) Recording of a PRESET»: it is fully automatic, any new modi-
fication of a parametric module is immediately recorded in
the last selected PRESET.
2) Access to the PRESETS:
- Direct access with the PRESET1, PRESET2, and PRESET 3
keys of the remote control.
- In the menu of the control pad: select « PRESET » with the
«  » et «  » keys (TP6 et TP3) then PRESET1, PRESET2,
or PRESET 3 with the «  » and «  » keys (TP4 et TP2).
I) DISPLAY MODE
Press the « DISPLAY » key on the remote to control to get the dis-
play "ON " or " OFF". The display mode can also be modified in the
setup menu using the keypad of the subwoofer.
Because of technical improvements already under way in our constant search
for optimum quality, Cabasse reserves the right to modify all the models pre-
sented in specification sheets, advertising materials and manuals without prior
notice.

Battery replacement:

take the remote control in your hand with the key
side facing the floor. Press the locker and pull out the battery-tray (picture 3a).
Remove the dead battery and replace it with another 3V lithium one, type
CR2025. Dispose of the old battery according to these instructions.
Disposal of battery packs / batteries
Do not dispose of battery pack/batteries into house hold
waste, fire or water. Battery packs/batteries should be col-
lected, recycled or disposed of in an environmental friendly
manner.
Only for EC countries:
dead
Defective or out battery packs/batteries must be recycled according the
guideline 91/157/EEC. For more detailed information about recycling of this
product, please contact your local city office, your household waste disposal
service or the shop where you purchased the product.