stayer SCR255W Instructions D'emploi page 31

made by cutting across the work piece. A 90º cross cut is
made whit mitre scale (13) set to 0º. Other setting will
cause mitre cross cut.
1.Pull the locking knob (28) and lift the cutting arm to its
full length.
2.Turn the locking knob (9)and press the lever (8) to
rotate the mitre table (7) until you reach the desired
position.
3.Release the lever (8) and retighten the locking knob
(9).
Warning! Make sure to tighten the mitre table before
making any cut, otherwise the table can move during the
cut and cause serious personal injury.
4.Place the work piece on the table with one edge
against the fence (6).
5.Make sure that there is no gap between the work piece
and the fence (6) or the mitre table (7).
6.If cutting long pieces of wood, support the opposite end
of the wood whit the support bar (5, 16) or whit other
working surface that is on the same level as mitre
table.
7.Use a clamp (18) to secure work piece whenever
possible.
8.Before switching the mitre saw on, perform a test run of
the cutting procedure to ensure everything works
properly.
9.Hold the operating handle (23) firmly and squeeze the
On/Off switch (24).
10.Allow the motor to reach full speed.
11.Release the blade guard release lever (25) and slowly
lower the cutting into the work piece.
12.To stop the mitre saw release the On/Off switch (24),
allow the saw blade to stop rotating and raise the
saw table (2) from the work piece.
Cross cutting (whit slide action)
Cross cutting enables the mitre saw to move back and
forth, allowing cutting wider work pieces.
1.Unscrew the slide bar lock (43) and pull the cutting arm
toward you.
2.Start the mitre saw as described above.
3.Lower the cutting arm into the work piece.
4.Push the cutting arm forward to complete the cut.
5.To stop the mitre saw release the On/Off switch (24),
allow the saw blade to stop rotating and raise the saw
blade (2) from the work piece.
ENGLISH
30
Bevel cut
The bevel cut can be set in the range from 0º to 45º. The
angle scale (33) located on the back side of the mitre saw
shows the currently position.
1.Loosen the angle lock knob (34) and move the cutting
arm to the left to the desired position (between 0º and
45º).
2.Tighten the angle lock knob (34).
3.For the cutting
mentioned above.
Laser Guide
Picture J. Built-in laser guide (44) clearly indicates line of
cut for increased cutting accuracy. Independent switch
(20) allows laser to be switched on and off easily. After
use please switch off the laser guide to save batteries.
Danger! Radiation is emitted from the device. Avoid skin
or eye exposure to the laser beam. So not look into the
laser beam or point it at other persons.
Mounting / removing the saw table
Picture F.
Danger! Disconnect the mitre saw from the power outlet
before inserting / changing the saw blade (2).
1.Pull the locking knob (28) to release the mitre arm.
2.Whit your index finger of the right hand push the blade
guard release lever (25), and open the blade guard
(1).
3.Unscrew the head screw (45) up to 7mm and push up
the protective cover (46) to expose head screw M6
(37).
4.Push up the blade guard (1) and screw in the head
screw (45) to lock the blade cover (1).
5.Press the saw blade lock (40), to lock spindle (39) and
loosen head screw (37), clamping flange (38) and
carefully remove the saw blade (2) from the spindle
(39).
6.After saw blade (2) is installed (or removed), unscrew
the head screw (45) to release blade guard (1) and
push it up.
7.Pull the protective cover (46) down and screw the head
screw (45) to fasten the saw blade (2).
8.To mount the saw blade (2) follow those steps in
reverse order.
30
procedure please follow steps