Specific Safety Instructions; Instructions For Use; Placement Tool; Assembly - stayer ISL122K Instructions D'emploi

Power tools are designed for tightening and loosening
screws, for drilling in wood, metal, ceramic and plastic,
and impact drilling in brick, concrete and stone.
1. Contents
2. Specific safety instructions ........................... 13
3. Instructions for use. ....................................... 13
3.1 Placement Tool .................................................. 13
3.2 Assembly ........................................................... 13
3.3 Electrical connection ......................................... 13
3.4 Illustrated description ........................................ 13
4.Operating instructions ............................................ 14
4.1 Placement and testing ..................................... 14
4.2 Tool change ...................................................... 14
5. Maintenance and service instructions ................. 14
5.1 Cleaning .......................................................... 14
5.2 Repair service ................................................. 14
5.3 Warranty.......................................................... 15
5.4 Disposal and recycling .................................... 15
6. Regulations ............................................................. 15
6.1 Technical Data ............................................... 15
6.2 EU declaration of conformity .......................... 15

2. Specific safety instructions

- Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
- Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
- Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
- Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
- In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and
seek medical help in case of complaints. The vapours
can irritate the respiratory system.
- Use the battery only in conjunction with your
STAYER power tool. This measure alone protects the
battery against dangerous overload.
Use only original STAYER batteries with the voltage
listed on the nameplate of your power tool. When using
other batteries, e. g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.

3. Instructions for use

ENGLISH
14

3.1 Placement Tool

Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
page
result in electric shock, fire and/or serious injury.

3.2 Assembly

Do not continue to press the On/Off switch after
the machine has been automatically switched off.
The battery can be damaged.
To remove the battery 5 press the unlocking buttons 9 and
pull out the battery downwards. Do not exert any force.
The battery is equipped with a temperature control which
allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achie-
ved in this manner. Observe the notes for disposal.

3.3 Electrical connection

Battery Charging
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
The battery is supplied partially charged. To
ensure full capacity of the battery, completely
charge the battery in the battery charger before
using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging
procedure does not damage the battery.
The lithium-ion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The inserted
tool no longer rotates.
Charge status indicator
The charging status indicator 10 of the magazine, is
composed of two LEDs:
Green: Displayed when the battery is charged.
Red: Displayed when the battery is charging.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be subject
to overload. When the load is too high or the allowable
battery temperature range of 0-50 °C is exceeded, the
speed is reduced. The power tool will not run at full speed
until reaching the allowable battery temperature.

3.4 Illustrated description

1 Screwdriver bit
2 Tool holder
3 Locking sleeve
4 Bulb
5 Battery
6 Handle
14