Technical Data; Before Starting The Equipment - EINHELL GE-CG 12 Li WT Mode D'emploi

Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Speed n : ............................................. 1200 rpm
0
Cutting width of the grass cutter: ............ 100 mm
Cutting width of the shrub shears ........... 190 mm
Cutting thickness of the shrub shears ........ 8 mm
Running time max.: .................................100 min
Battery pack: ................ Li-Ion / 12 V d. c. / 1.5 Ah
Charging time: ................................................ 2 h
L sound pressure level: ...................... 61 dB (A)
pA
L sound power level: ......................... 81 dB (A)
WA
K uncertainty ................................................. 6 dB
Vibration max. a : ................................... 5.5 m/s
h
K uncertainty ............................................1,5 m/s
Weight: .......................................................0.8 kg
Sound pressure level
at the operator's ear .............................. 77 dB (A)
K uncertainty ........................................... 3 dB (A)
Battery charger
Mains voltage.....................100-240 V ~ 50-60 Hz
Output
Rated voltage .......................................... 13 V DC
Rated current: .......................................... 900 mA
The vibration emission level has been measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
•
The specified emission level can also be
used to make an initial assessment of the ex-
posure to vibrations.
Warning!
The vibration emission level may vary from the le-
vel specifi ed during actual use, depending on the
way in which the power tool is used.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
Anl_GE_CG_12_Li_WT_SPK9.indb 16 Anl_GE_CG_12_Li_WT_SPK9.indb 16
GB
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
2
maintained.
2

5. Before starting the equipment

5.1 Charging the battery pack (Figure 3, 4)
•
Connect the charger to the charging station
(Figure 3).
•
Check that your mains voltage is the same
as that marked on the rating plate of the bat-
tery charger. Plug the battery charger in a
socket-outlet. The red LED (Figure 4 / Item 1)
comes on to indicate that charging voltage is
available.
•
The battery pack is being charged. An empty
battery pack requires a maximum charging
period of 2 hours. The temperature of the bat-
tery pack may rise slightly during the charging
operation. This is normal.
•
As soon as battery pack is fully charged, the
red LED (Fig. 4/Item 1) extinguishes
If the rechargeable battery fails to charge, check
whether there is voltage at the socket outlet.
Timely recharging of the battery pack will help
it serve you well for a long time. Recharging is
always necessary when you notice a drop in the
tool's performance.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
- 16 -
03.05.2017 14:55:33 03.05.2017 14:55:33