Triton ETA300 Instructions D'utilisation Et Consignes De Sécurité page 7

STEP 8
Loosely fit the Phillips Screws (23) and Square Nuts (24)
through the holes in each Leg Clamp Assembly (20) as
shown in the top inset Fig. 3. Tap the assemblies onto the
ends of the Outer Track (16) locating the screws in the
notches.
Loosen the large round knobs and align the cut-outs in
the clamps with the square cut-outs in the track. Insert
the legs through the track cut-outs and tighten the large
round knobs to clamp. Now tighten the Phillips Screws
(23). Slide the height stops up the leg slots until they
touch the outer track and tighten into position. They help
set the correct height for future set ups, and serve as
protection against track slippage under heavy load.
FITTING THE INNER TRACK
STEP 9
Loosely bolt the Support Brackets (31) to the brackets
on the Inner Track (30) using the short Coach Bolts (35),
Washers (13) and Nyloc Nuts (22), (Fig. 4). Do not tighten
yet. Note the orientation of the brackets in regard to the
long overhang of the inner track (Fig.4).
Loosely fasten the longer Coach Bolts (26) and Round
Knobs with Nuts (27) onto the support brackets (Fig. 4).
Unscrew the large round knob (one turn only) on each
Skid Assembly (32) and insert them into the ends of the
inner track. With the skids pointing up, firmly tighten the
knobs.
STEP 10
Fasten the two Locking Latches (36) onto the latch
brackets using the Hex Bolts (37) and Nyloc Nuts (22).
Ensure the rectangular windows in the latches are
oriented as shown in Fig. 4. Tighten the bolts until the
latches pivot firmly.
STEP 11
Fit the Front and Rear Panel Brackets (33) and (34) to the
left-hand side of the Workcentre (when viewed from the
front panel, which has the switchbox). The brackets are
left or right handed. The long edge flanges should wrap
around the faces of the end panels (Fig. 5).
At the top of each bracket, use the bolt, washer and nut
which hold the left-hand bearing channel in position. At
the bottom of each bracket, fit the Phillips Screw (38) and
Flange Nut (10), do not tighten yet.
Note: if you have a MK3 Workcentre or an early Series
2000 Workcentre (pre- serial no. 305000) it will be
necessary to drill the lower holes through the end panel
flanges. If drilling, make sure you position the holes as
shown in the inset in Fig. 5, to give you the full range of
height adjustment in the bracket. Centre punch the hole
positions and drill ⁄ " or 6.5mm holes.
1
4
Fit the inner track to the Workcentre by locating the coach
bolt heads through the keyholes in the end panel brackets
(Fig. 6). Tighten the round knobs and then temporarily
tighten the four Nyloc Nuts (22) holding the inner track to
the brackets.
ALIGNING THE TRACKS
STEP 12
On Series 2000 Workcentres, push the legs of the
Workcentre diagonally outwards to ensure that it is fully
stable on the folding stand.
Position the outer track parallel to the inner track
approximately 700mm away from it. Place the table onto
the tracks with the inner (smaller) bearings on the inner
track. Always fit the table in this orientation. Slide the
table to each end of its travel and adjust the position of
the outer track. The lengthened outer bearings make this
a non-critical adjustment.
STEP 13 - Adjusting Inner Track Height
Next you have to fine-tune the height of the inner track.
Fit the extension table fence to the sliding table so that
it extends across the Workcentre table (Fig. 12). Loosen
the front bearing channel bolt and adjust the height of the
front panel bracket until the bottom of the fence is around
0.5 - 1mm above the Workcentre table. Slide the table to
the rear of the workcentre and adjust the height of the
rear bracket. Tighten the bolts and Phillips screws holding
the brackets to the end panels.
STEP 14 - Adjusting Outer Track Height
Next, adjust the height of the outer track until the fence is
level, and parallel to the Workcentre table.
Check the table throughout its travel for diagonal rocking
on the tracks, and fine tune the height of the outer track if
necessary. Adjust the height stops on the outer track legs
to lock-in the correct height.
With the sliding table
positioned midway along
the tracks, engage the
front and rear locking
latches (Fig. 7).
Adjust the Phillips screws
until the heads enter the
rectangular windows and
the table cannot be lifted.
(It will be necessary to unlock the latches and lift the table
clear to make these adjustments).
STEP 15 - Fine-tuning the Inner Track
The last step is to fine-tune the inner track position in the
horizontal plane, to ensure that the extension table scales
are accurate.
Series 2000 Workcentres: With the extension table
fitted and locked, and the rip fence removed, insert the
standard Workcentre rip fence and set it to 500mm using
the end panel calibration marks.
Fig. 7
Assembly
7
GB