Floorcleaning - Interline ECO FILTER SET Instructions De Service

You bought a technical device, the handling is easy and simple,
but requires the observance of certain precautions. We therefore
ask you to read the following instructions carefully! For the
operation of the filter system, you need a skimmer (surface
skimmer). Either an integrated skimmer (built into the pool wall)
or a suspended skimmer (attachment to the poolwall).
POSITIONING
The installation area you set between the skimmer and the inlet
nozzle so, that there is an adequate safety margin to the pelvic
wall. We recommend putting the filter system in addition on
base plates (for example: washed concrete slabs etc.). These have
to be installed with the spirit level. Under no circumstances you
may put your filter system in a trough or directly into the grass
(flood danger or risk of overheating of the filter pump). If you
have sunk your pool partially or completely, so it makes sense to
place the filter pump in a filter slot, which should connect
directly to the pelvis. Is your filter pump housed in a filter slot, so
it has to be insured, that the filter slot can't be slooded. For this
purpose you should bring in a roller-burnishing (crushed rock) in
the range of the fil-ter slot, so that the surrounding- and
rainwater can seep away. It would be ideal if there is a direct
connection to the drain in the sump of the filter shaft (or sludge
pump, with automatic floating switch). It is important to ensure
that the filter slot should never be airtight, because this may
cause damage, due to condensa-tion water, on the filter pump.
The size of the filter shaft should be selected so that work can be
performed on the filter system. The necessary accessories such as
hoses, hose clamps and filter sand (not included) are offered
gladly from your pool dealer.
ASSEMBLY OF THE FILTER SYSTEM
Install the filter system at least 3.50 meters away from the edge
of the swimming pool. The filter pump can be connected to a
grounded electric supply with an alternating voltage of 230 V
and 50 HZ and must be protected by a differential switch (RCD)
with a sensitivity not above 30 mA.
The filter pump consists of the following parts (Illustration 1):
1. Pump
2. valve
3. Seal (O-Ring)
4. clamping ring
5. vessel
6. Central pipe
7. Filter screen
8. Drain plug
9. Centralizer (cover for standpipe)
10. Base plate
11. Pressure hose
FILTER VESSEL
»
Insert stand pipe including filter screen into boiler (Figure 2)
»
Place the stand pipe with the filter screen on the floor of
the boiler, make sure that the stand pipe is located in the
middle of the boiler and that the drain plug is screwed in.
»
Now put the centralizer on the tank opening, while cente
6
EN
ring the standpipe. (Illustration 4)
»
Fill in the filter quarz sand or Fiberclean up to a high of
about ¾ of the bowlhight. (right grit 0,4mm - 0,8mm,
Quantity: depending on filter size) (Illustration 4)
»
Then mount the top oft he boiler or the valve head and the
boiler seal on the tank top of the filter vessel. Before you do
this, it is neccassary to clean again and wash off any sand or
accumulated debris. The connection of the top of the boiler
or the head valve with the filter vessel is carried out by the
clamping ring. The clamping ring is screwed with the
clamping ring screw and the collet nut. (Illustration 5 & 6)
»
Finally, mount the pump fittings on the valve head. Seal the
pump fittings sufficiently by using teflon tape.
»
The pressure gauge (if included) is screwed to the side of
the 7-way valve and sealed. The existing vent plug should
be removed first. (Illustration 9)
PUMP HOSE CONNECTIONS
»
Skimmers: Connection from skimmer to the front
connector of the filter pump. (Illustration 7)
»
Pressure line: Connection going from the upper area of the
top of the filter pump to the connector with the designati
on "PUMP" at the 7-way valve.
»
Return line: Connection from the 7-way valve with the de
signation "RETURN" to the connection at the inlet nozzle
(pool). Secure all connections with hose clamps.
»
Backwash: Connection „WASTE" (Empty) in the channel.
Connections are made with special pool hoses and hose
clamps!
COMMISSIONING OF THE FILTER SYSTEM
»
Before you go in operation with the filter system, it must
be insured that the filter system stands outside the basin
and in the level lower than the water level of the pool is,
and the hose connections are properly connected and
secured.
»
The swimming pool must be filled with water, according
to the instructions of your pool dealer. The water must
flow towards the filter pump. Now the filter pump is
vented. If available, open slightly the preliminary filter
of the filter pump until water flows from the prefilter top.
(transparent cover with screw connection on the top of the
filter pump) For non self-priming pumps, it is neccassary
that the water level is above the filter pump.
»
Place the handle on the 7- way valve to the Backwash
position. Only now the filter pump is taken in operation.
Backwashing about 2 - 3 minutes to perform. Then turn
the filter pump off again and put the handle on the valve
head in the RINSE position. Rinsing for 30 seconds.
Thereafter, the filter pump is switched off again and the
handle set to the position FILTER. The backwashing and
rinse water you best pipe in the channel.
»
Turn the filter pump back on. The filter system is in normal
filter operation. We recommend a filter run time of 2 x 4 - 5
hours per day. If you clean the bottom of your pool with a
pool vacuum cleaner, this is also done in the position filter.
After each floorcleaning or when the pressure on the
pressure gauge if available (by 2 - 3 ticks) rises, backwashing
is required.
»
After BACKWASHING always a REFLUSHING with a duration
of approximately 30 seconds is required. This causes the
reduction of the sand in the filter vessel.
»
If you clean your pool with a pool vacuum cleaner, this
can also be done with the 7-way valve in the position
DRAINING to remove impurities from the pool (eg: algae),
which otherwise go back through the filter sand. In doing
so, the water which is extracted from the ground, will
be directly pumped through the backwash line into the
open air. After this process, the water level of the pool is
supplemented accordingly.
FILTRATION SYSTEMS MAY NOT RUN DRY (WITHOUT
WATER)!
THE WATER TAKES THE COOLING – IN CASE OF DRY
RUNNING THERE IS NO WARRANTY REPLACEMENT!
WITH EVERY SWITCHING OF THE 7-WAY VALVE THE FILTER
PUMP MUST BE TURNED OFF!
Filter run time (2 x 4 – 5 hours a day) and the regular
backwashing (2 – 3 minutes) at least 1 x per week as well as the
floorcleaning are the basic requirement for maintained swim-
ming pool water! Repairs on the pump should only be perfor-
med by trained and qualified, professional technicians.
SPECIFICATIONS
, ,
All models: 7-way valve, Filter pump TÜV / GS Filter vessel
Connection Ø 32/38 mm, Base plate.
Model INTERLINE SQ-ECO
Pump flow rate 3.6 m 3 /h at 0,4 bar working pressure
Connection 230 V, max. 200 W
Amount of sand max. 20 kg
Filter pump without prefilter, not self-priming
Model INTERLINE SQ-JUNIOR
Pump flow rate 4.5 m /h at 0,4 bar working pressure
3
Connection 230 V, max. 250 W
Amount of sand max. 20 kg
Filter pump without prefilter, not self-priming
Model INTERLINE SQ-SENIOR
Pump flow rate 6.5 m /h at 0,4 bar working pressure
3
Connection 230 V, max. 450 W
Amount of sand max. 30 kg
Filter pump without prefilter, not self-priming
Model INTERLINE SQ-SUPER
Pump flow rate 8.0 m 3 /h at 0,4 bar working pressure
Connection 230 V, max. 550 W
Amount of sand max. 68 kg
Filter pump without prefilter, not self-priming

FLOORCLEANING

Floorcleaning is done in position filtering (on the valve). The
poolfloor vacuum cleaner has to be connected with the pool-
floor vacuum cleaner hose directly to the skimmer. Until the
pool-floor vacuum cleaner is connected and ready for operati-
on, the filter pump must be switched off.
Important: The pool-floor vacuum cleaner hose must fully be
filled with water so that the pump does not filter air, only then
the pump can be switched on. Will air get into the filter system,
the filter pump is to turn off and the vacuum cleaner must be
vented again.
Now move slowly and smoothly (speeding can stir up dirt) with
your vacuum cleaning brush on the bottom of the pool. For
filter systems without prefilter a skimmer with a strainer basket
is beneficial!
PROBLEM TREATMENT
Cause of Problems Solution
Backwashing (cleaning of the
Sand contaminated with dirt
sand)
Pump sucks air Defective hoses,
(Bubbles at the inlet) tighten hose clamps
Check water level and
Skimmer or pump gets too increase if necessary, check
little water the intake for dirt
accumulation
Cleaning of the skimmer
Skimmer basket contaminated
basket
Prefilter basket of the filter Cleaning oft he prefilter
pumpcontaminated basket
TO WINTERIZE THE SYSTEM
At the end of the swimming season, the filter system and the
hoses must be removed and emptied. This is done when the
filter vassel as well as the filter pump by opening the drain plug.
Open the filter vessel and empty the filter sand. Verify that the
filter sand is still in reasonable condition (not glued or clumped)
and clean it. Filter systems located outdoors must be located in
a frost-free room in the winter.
CARE INSTRUCTIONS
Visible contaminants are removed through the filtration system.
This is not true for algae, bacteria and other microorganisms,
which arealso a constant threat to clear, clean and healthy pool
water. For their prevention or removal, special water treatment
is available, properly and permanently dosed, guarantee for
swimmers any kind of harassment and ensure proper hygienic
bath water.
Important Note: On the side of the 7-way valve handle is a lot
number shown, please provide this data in the case of a com-
plaint.
7