Eco Mode; Manual Mode; Program Zone Mode; Reverse Function - Hillyard TRIDENT R26SC PLUS Manuel D'utilisation Et D'entretien

ATTENTION: The drying without scrubbing operation should only be carried out if the device was used beforehand to carry out a scrubbing without drying
operation.
3
1
2
1
2

ECO MODE

In the centre of the control panel there is the ECO-MODE button (1). Press it to activate the "ECO-MODE" program, which provides the best possible performance in terms of consumption and cleaning.
To activate the ECO-MODE program, proceed as follows:
1. Sit on the driver's seat.
2. Insert the key (1) into the main switch on the control panel. Set the main switch to "I" (Fig.1).
3. Select the ECO-MODE working program with the button (2) at the centre of the control panel (Fig.2).
N.B.: As soon as the button (2) in the control display is pressed, the "ECO-MODE ACTIVE" symbol (3) will appear (Fig.3).
4. Press the drive pedal (4) to begin moving the machine (Fig.4).
N.B.: to activate the ECO-MODE function, you can also press, with the transfer working program active, the "BRUSH HEAD CONTROL" button (6) or the "SQUEEGEE CONTROL" button (7) (Fig.2).
Pressing one of the two buttons will switch from the transfer program to the relative program selected, and the symbol (3) will appear in the control display.
7
1 5
1
2

MANUAL MODE

To change from the "ECO MODE" or from the "PROGRAM ZONE" mode to the "MANUAL MODE", simply change one of the following parameters:
A. Quantity of detergent solution present in the machine's water system (read paragraph
B. Machine's forward speed level (read paragraph
1
C. Suction motor performance level (read paragraph
1
D. Pressure level exerted on the brush head (read paragraph

PROGRAM ZONE MODE

The "PROGRAM ZONE" modes foresees the use of three functions already stored in the machine's internal memory, levels:
• Forward speed
• Adjustment of the detergent solution flow
2
• Suction motor efficiency
1
are pre-set and have been created on the basis of the type of environment where you want to work.
To select an area program, just press the relative button (1) on the control panel (Fig.1).
1

REVERSE FUNCTION

This machine is equipped with electronic traction control. To reverse, proceed as follows:
1. Engage the "REVERSE GEAR ACTIVATION/DEACTIVATION" lever (1) underneath the steering wheel (Fig.1).
2. Press the drive pedal (2) (Fig.2); in this manner the machine will begin to move in reverse.
CAUTION: the reverse speed is lower than the forward speed to comply with current health and safety standards.
1
N.B.: In order to disengage the reverse gear, disengage the lever (1) underneath the steering wheel (Fig.1).
1
N.B.: Once the lever has been engaged (1), the acoustic signalling device will be activated in order to signal that the machine's reverse gear has been engaged.
N.B.: If the reverse gear is engaged with the squeegee in its working position, once the drive pedal is pressed, the machine will begin to move in reverse and the squeegee
body will be raised into its resting position.
N.B.: If the reverse gear is engaged with the brush head in its working position, once the drive pedal is pressed, the machine will begin to move in reverse and the brush
head will remain in its working position, but the solenoid valve will stop dispensing detergent solution to the brushes.
2
2

BUZZER

The machine is equipped with a buzzer. if you need to sound a warning, just press the button (1) on the steering column (Fig.1).
1
1
3
2
6
3
3
"REGULATING THE FORWARD
N.B.: When the "MANUAL MODE" is active in the control display the symbol (1) relative to the "ECO MODE ACTIVE" function will disappear.(Fig.1).
N.B.: when an area program is active, the relative LED (2) will light up on the control panel (Fig.1).
N.B.: if you want to change the levels of the above parameters of the "AREA" functions, just make the necessary modifications then press and hold the button of
the relative program for about three seconds. The modification will be recorded when the LED starts flashing.
4
4
"ADJUSTMENT OF THE DETERGENT SOLUTION
SPEED").
"SILENT-MAX FUNCTION").
"EXTRA BRUSH HEAD PRESSURE FUNCTION").
17
4
FLOW").