Max Re-Bar-Tier RB398S Mode D'emploi Et Consignes De Sécurité page 9

11. USE ONLY THE AUTHORIZED BATTERY PACK
If the tool is connected to a power supply other than the
authorized pack, such as a rechargeable battery, a dry cell,
or a storage battery for use in automobiles, the tool may be
damaged, break down, overheat, or even catch on fire. Do
not connect this tool to any power supply except the
authorized battery pack.
12. TO ENSURE MAXIMUM PERFORMANCE, FULLY
CHARGE THE BATTERY BEFORE USE
A new battery pack or one not used for extended periods
may have self-discharged and thus may need recharging to
restore it to a fully charged condition. Before operating the
tool, make sure to charge the Battery pack with the
designated MAX Battery charger.
13. BATTERY CHARGING PRECAUTION
13-1 Use only MAX Battery charger and MAX
Battery pack.
Failure to do so may cause the Battery to overheat or
catch fire leading to serious injury.
13-2 Charge the Battery from an AC 100-240V
wall sockets.
Failure to do so may result in overheating, or
inadequate charging possibly causing serious injury.
13-3 Never use a transformer.
13-4 Never connect the Battery charger to an
engine generator direct-current power
supply.
The charger will break down or be damaged from
burning.
13-5 Avoid charging the Battery pack in the rain,
in a damp place, or where water is
splashing.
Charging a damp or wet Battery pack will cause an
electric shock or a short circuit that may lead to
damage from burning and even the tool catching on
fire.
13-6 Do not touch the power cord or plug with a
wet hand or glove.
This may cause injury from electric shock.
13-7 Do not put a cloth or any other cover on the
Battery charger while the Battery pack is
being charged.
This will cause overheating and damage from burning,
or the Charger may even catch fire.
13-8 Keep the Battery pack and Battery charger
away from heat and flames.
13-9 Do not charge the Battery pack near
flammable materials.
13-10 Charge the Battery pack in a well ventilated
place.
Avoid charging the Battery pack where it will be in
direct sunlight.
13-11 Charge the Battery pack in a temperature
range of 41°F (5°C) to 104°F (40°C).
13-12 Avoid continual use of the Battery charger.
Rest the Charger for 15 minutes between charges to
avoid functional trouble with the unit.
13-13 Any objects that block the ventilation holes
or Battery pack receptacle may cause
electric shock or functional troubles.
Operate the charger free of dust or other foreign
materials.
13-14 Handle the power cord carefully.
Do not carry the Battery charger by its power cord. Do
not use the power cord to disconnect it from a wall
socket; this will damage the cord and break the wires
or cause a short circuit. Do not let the power cord
contact sharp edged tools, hot materials, oil, or
grease. A damaged cord must be repaired or
replaced.
13-15 Do not charge non rechargeable batteries
with this charger.
13-16 This charger is not intended for use by
children or disabled persons without
supervisor.
13-17 Children should be supervised to ensure
that they do not play with the charger.
13-18 Put a Pack cap (Fig.2.i) on the Terminal
(Fig.2.j) of the Battery pack.
When the Battery pack is not in use, put a Pack cap on
its Terminal to prevent short circuits.
13-19 Do not let the Terminal (metal component)
of the Battery pack short-circuit.
A short circuit in the Terminal will generate a large
current, causing to overheat the Battery pack and
become damaged.
13-20 Do not leave or store the tool in a vehicle or
in direct sunlight during summer. Leaving
the tool in high temperature conditions
may cause the Battery pack to deteriorate.
13-21 Do not store a fully discharged Battery
pack. If a fully discharged Battery pack is
removed from the system and left for a
long period of time, it may become
damaged. Recharge the Battery
immediately when it has been discharged.
14. WEAR SAFETY GLOVES WHILE OPERATING THE
TOOL
The finish tie has sharp edges. To avoid serious injures, be
careful not to touch the sharp edges. MAX recommends
wearing safety gloves while operating the tool.
15. PRIOR TO USING THE TOOL
(Fig.4 and 5) Make sure that the safety features function
properly. If they do not, avoid using the tool.
9