Maintenance; Cleaning Manual; Storage - Max Re-Bar-Tier RB398S Mode D'emploi Et Consignes De Sécurité

13. MAINTENANCE

1-1 Regularly inspect the tool
In order to maintain the performance of the tool, periodically
clean up and inspect the tool.
1-2 Do not lubricate the equipment
Absolutely do not lubricate this equipment. Applying
lubrication will remove the grease inside of the tool, and
cause problem on the tool.
1-3 (Fig.27) Regularly clean the feeding mechanism
In order to maintain the performance of the tool, periodically
clean up the mechanism around the feed gear. Using the Air
Duster or like, blow the dust and the iron sand off around the
feed gear.

14. CLEANING MANUAL

When the machine operates for long hours, dust and wire
cuttings may adhere to the cutter section. In such a case,
disassemble and clean the machine according to the following
procedure. (If a wire is caught in the cutter section or wire guide
A, the wire can be removed according to the same procedure.)
(RB398S)
Disassembling
NOTICE
• Do not remove the 2 uncoated bolts.
1-1 Loosen the 2 (plated) Hexagon socket head bolts M3 × 6
(Fig.28.o)
1-2 Remove Arm B (Fig.29.t) and the 2 (plated) Hexagon
socket head bolts M3 × 6 (Fig.29.o).
1-3 Remove the Cutter (Fig.30.p) and the Fixed cutter
(Fig.30.r), and clean them. (The removable parts are the
Cutter (Fig.30.p), Fixed cutter(Fig.30.r), Wire guide A
(Fig.30.q) and Cutter plate unit.(Fig.30.s).
Assembling
NOTICE
• (Fig.31) Assemble the Fixed cutter (Fig.31.r) so that the
Large hole (Fig.31.b) is set to the rear side and the Small
hole (long hole) (Fig.31.c) is set to the top side.
Rear side
1-4 Put the pin of the cutter plate unit (Fig.31.s) through the
Cutter connecting rod hole (Fig.31.u) and assemble the
fixed cutter (Fig.31.r) to the unit.
1-5 Fit the Cutter (Fig.32.p) and assemble Wire guide A
(Fig.32.q).
1-6 Align the groove (Fig.33.v) of Wire guide B (Fig,33.w)
attached to Arm B (Fig.33.t) with the Pipe (Fig.34.n), and
assemble Arm B.
1-7 (Fig.35) Make sure that Arm B is securely assembled and
tighten the 2 (plated) Hexagon socket head bolts M3 × 6.
(Fig.35.o) (Tightening torque: 15.5 lbf·in (175 cN·m))
NOTICE
• (Fig.36) Are there any loosening parts?
Make sure that the outer parts are aligned and the parts are
securely assembled without any gap between them.
(RB518) (RB218)
Disassembling
1-1 (Fig.41) Loosen the 2 (plated) Hexagon socket head bolts
M3 × 5 (Fig.41.y).
1-2 (Fig.42) Remove Arm B (Fig.42.z) and the 2 (plated)
Hexagon socket head bolts M3 × 5 (Fig.42.y).
Top side
15
1-3 (Fig.43) Remove the Cutter (Fig.43.D) and the Fixed cutter
(Fig.43.C), and clean them. (The removable parts are the
Cutter, Fixed cutter and Step pin (Fig.43.B).)
Assembling
NOTICE
• (Fig.44) Assemble the Fixed cutter (Fig.44.C) so that the
Large hole (Fig.44.G) is set to the Rear side and the Small
hole (Fig.43.H) is set to the Top side.
Rear side
1-4 (Fig.45) Insert the step pin (Fig.45.B) into the hole and then
into the Connecting rod (Fig.43.F) hole. Make sure the
Step pin is fully inserted.
1-5 (Fig.46) Make sure that Arm B (Fig.41.z) is securely
assembled and tighten the 2 (plated) Hexagon socket head
bolts M3 × 5 (Fig.46.y). (Tightening torque: 15.5 lbf·in
(175 cN·m))
NOTICE
• The (right) bolt (Fig.46.y) should have the Washer
(Fig.46.E). Install the washer first and then tighten the
bolt.

15. STORAGE

Do not store the tool in a cold weather environment. Keep the tool
in a warm area. When not in use, the tool should be stored in a
warm and dry place. Keep out of reach of children. All quality
tools will eventually require servicing or replacement of parts
because of wear from normal use.
(Fig.21) Remove reel of Tiewire
When you have finished the Tiewire, remove the Tiewire from the
tool.
Store the tool
When you have finished tying work or when the tool will not be
used for a while, switch off the tool, make sure the motor has
stopped, lock the trigger, and remove the battery pack. Tool,
attachments and accessories should be stored in a well-
ventilated dry place where the temperature will not exceed 104°F
(40°C). The battery pack, with a pack cap installed on the pack's
terminal to prevent short circuits, should be stored in a well-
ventilated dry place where the temperature will not exceed 86°F
(30°C).
Top side