Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
4.1.5
Radio / Bluetooth function.
Touch the "
"button on the control panel to turn on the radio. The display will now show the current radio channel,
frequency and volume. Touch this button again to turn off the radio and proceed to the bluetooth music function. Touch
the button again to turn off the music function.
When the radio is on, touch the "
time you can change the volume by touching the "
15. When the radio is on, and you touch the "
time you can change the frequenzy 0.1Mhz by touching the "
Touch and hold one of these buttons for 2 seconds to search for channels, as it will stop when it finds a channel and
play it. When you get the channel you need, just wait shortly and the system will exit the setting state. Touch and hold
the "
"button for 2 seconds to save the current channel. After you successfully saved the channel you will see its
number on the display as is shown in fig.11. The system is able to save 10 channels in total. When the radio is on and
you touch the "
to choose the radio channel you like.
When the system is on, use the bluetooth function on your bluetooth device to search the signal of the bathtub with the
name "SANJUN MUSIC".You can adjust the name to your own liking with your bluetooth device. Pair the device, if the
connection fails for some reason, the bluetooth icon "
Touch the "
" button twice to go to bluetooth music, you then see the "
Now you can play the song from your bluetooth device. Touch the "
When the bluetooth music is playing a song, use the "
fig.14. Touch the "
When the bluetooth mode is on, use the "
or "
"button to choose the song you like. Bluetooth music will turn off automatically 10 seconds after the system is
turned off.
4.1.6
Clean function.
When the system is on and the water level is sufficient, touch the "
the clean menu as is shown in fig.16. To initiate, touch the "
"
"icon. To abort the clean cycle touch the "
1. 8 Seconds after activating the clean function the hydro pump and aero pump start.
2. After 7 seconds the clean valve opens for 3 seconds and switches off automatically.
3. After this the hydro pump and aero pump operate for 80 seconds followed by a 20 seconds pause. After this 20
seconds the hydro pump and aero pump resume operating for 90 seconds. After these 90 seconds the clean cycle
is finished and it will turn off automatically.
When trying to turn on the clean function when there is not enough cleaning liquid in the tank you will see the
"
"icon appear in the screen in a blinking mode. After 3 seconds the icon will disappear.
4.1.7
Thermostat.
The thermostat function is restricted by the hydro pump function. Touch the "
function. The heater needs to work simultaneously with the hydro motor, therefore the hydro button will light up
together with the heater button. To turn off the thermostat function you can touch the "
"
"button. The hydro pump can only be stopped when you touch the "
IW00372.2
EN
Figure 9
"button and you will see the volume on the display as shown in fig.9. At this
"button three times till you see the icon as it shows in fig.12. Touch the "
Figure 13
" or "
"button to adjust the volume.The volume range is from level 0 to level 15.
Figure 14
"button to go to the screen as it shows in fig.15. Now touch the "
Figure 16
Figure 10
" or "
"button. The volume range is from level 0 to level
"button multiple times, you will see the display as in fig.10. At this
" or "
" will flash. If this happens, please try to connect it again.
"button to turn off the bluetooth function.
"button to go to the volume adjusting menu as shown in
Figure 15
"button followed by the "
"button and the "
"button.
-10-
Figure 12
Figure 11
"button. The range is from 87.5-108Mhz.
" or "
"icon on the display as in fig.13.
"button to go to
"icon will change into an
"button to turn on the thermostat
"button as well as the
"button. The heater will only turn on
"button
"
Publicité
Chapitres
Table des Matières
