Display Setting - Yamaha BD-S667 Mode D'emploi

SETUP MENU
IP Setting
You can set IP Setting to Auto/Manual. When set to Auto,
IP address is allocated automatically by system. When set
to Manual, IP Address, Subnet Mask, Default Gateway
and DNS should be set manually.
*
Auto , Manual
BD-Live Connection
You can set access restriction to BD-Live contents.
* Allows all BD-Live discs to connect the network.
Permitted
Partial Allows only discs with owner certification.
Permitted
Prohibited Prohibits all BD-Live discs to connect the network.
DLNA
You can set the DLNA (p. 19) to Enable/Disable. When
you do not use the DLNA function, set to Disable.
*
Enable , Disable
Proxy Setting
You can set Proxy Setting. Set to Disable for normal use.
* Sets proxy server to disable. Select this item when
Disable
proxy server is not used.
Proxy Host Sets the proxy host.
Proxy Port
Sets the proxy port.

■ Display Setting

The default settings are marked with "
TV
TV Screen
You can set the screen aspect ratio of the connected TV,
and adjust the video output.
If you switch your TV (i.e. because you have bought a
new one) and the screen aspect ratio of the connected TV
changes, you will have to change the TV Screen setting.
16:9 Full
Select this when this Player is connected to a TV
with a 16:9 screen. When a 4:3 aspect ratio video is
played back, the video is displayed as shown below.
* Select this when this Player is connected to a TV
16:9 Normal
with a 16:9 screen. When a 4:3 aspect ratio video is
played back, the video is displayed as shown below.
4:3 Pan Scan Select this when this Player is connected to a TV
with a 4:3 screen. When a 16:9 aspect ratio video is
played back, the video is displayed as shown below.
4:3 Letterbox Select this when this Player is connected to a TV
with a 4:3 screen. When a 16:9 aspect ratio video is
played back, the video is displayed as shown below.
On 16:9 (wide screen) TV
Original
image size
16:9 Full
4:3
28
En
Resolution
You can select the video output resolution from Auto,
480i/576i, 480p/576p, 720p, 1080i, and 1080p. When set
to Auto, resolution is set to the maximum resolution
according to the connected TV. For more details on output
formats, refer to "About the video output formats" (p. 30).
Auto
TV System
You can select TV System from PAL, NTSC and Multi.
Set the same TV System as your TV set. For more details
on output formats, refer to "About the video output
formats" (p. 30).
NTSC
Color Space
".
*
You can select the Color Space (p. 35) output from
HDMI. This function is available when this Player is
connected with an HDMI cable.
RGB
YCbCr
YCbCr422
HDMI Deep Color
When your TV and/or AV receiver is compatible with
Deep Color (p. 35), set this item according to your TV/AV
receiver. This function is available when this Player is
connected with an HDMI cable.
30 bits, 36 bits, Off
HDMI 1080p 24Hz
This outputs the BD-Video encoded in 24Hz frame rate in
HDMI 1080p 24Hz. Smoother video playback may be
available with this function. This function is available
when your TV/AV receiver support this function, and this
16:9 Normal
Player is connected with an HDMI cable. For more details
on output formats, refer to "About the video output
formats" (p. 30).
On, Off
Original
image size
4:3 Pan Scan
16:9
*
, 480i/576i, 480p/576p, 720p, 1080i, 1080p
*
, PAL, Multi
Note
– When no picture is displayed after this setting is
changed, press and hold
around 5 seconds to switch NTSC/PAL manually.
Outputs video signal at normal signal range.
* Sets Color Space to YCbCr.
Sets Color Space to YCbCr422.
Note
– This function is only available on TVs that support
this function.
*
*
Note
– This setting is disabled when output resolution is
other than 1080p.
On 4:3 TV
4:3 Letterbox
on the front panel for