Proper Use; Technical Data - EINHELL TC-TS 2031 U Instructions D'origine

•
Sawblade guard
•
Push stick
•
Parallel stop
•
Rubber foot (4x)
•
Cross stop rail
•
Chassis
•
Parallel stop rail
•
Guide rail (2x)
•
Leg A (1x)
•
Cross strut (2x)
•
Longitudinal strut (2x)
•
Leg (3x)
•
Blade change tool
•
Tool hook
•
Extraction hose
•
Allen key
•
13/19mm ring wrench
•
Open-ended wrench
•
Table length extension
•
96mm extractor adapter
•
Holder for extraction hose
•
Handle (2x)
•
Strut for table length extension (2x)
•
Slide block (not shown)
•
Assembly material
•
Original operating instructions
•
Safety information

3. Proper use

The bench-type circular saw is designed for the
slitting and cross-cutting (only with the cross
stop) of all types of timber commensurate with the
machine's size. The equipment is not to be used
for cutting any type of round wood.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The equipment is to be operated only with suita-
ble saw blades (saw blades made of HM or CV)
It is prohibited to use any type of HSS saw blade
and cutting-off wheel.
Anl_TC_TS_2031_U_SPK9-1.indb 26 Anl_TC_TS_2031_U_SPK9-1.indb 26
GB
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossi-
ble to eliminate certain residual risk factors.
The following hazards may arise in connection
with the machine's construction and design:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut
injuries).
•
Kick-back of workpieces and parts of work-
pieces.
•
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the saw
blade.
•
Damage to hearing if essential ear-muffs are
not used.
•
Harmful emissions of wood dust when used
in closed rooms.

4. Technical data

AC motor ......................................... 230V ~ 50Hz
Power P .................................. S2 20 min 2000 W
Speed n0 ........................................... 2950 min
Carbide saw blade ...........Ø 315 x Ø 30 x 3.0 mm
Number of teeth ............................................... 40
Table size .......................................800 x 550 mm
Table length extension ...................800 x 400 mm
Cutting height max. ...........................85 mm / 90°
..........................................................52 mm / 45°
Height adjustment .....................infi nite 0 - 85 mm
Tilting saw blade ...........................infi nite 0° - 45°
Max. workpiece width.................................. 1.6 m
Extractor connection ................... Ø 36 / Ø 96 mm
Weight.............................................approx. 54 kg
Protection class:.................................................. I
Thickness of the splitter: .......................... 2.6 mm
- 26 -
-1
02.12.2019 07:41:43 02.12.2019 07:41:43