Starting The Equipment; Cleaning And Maintenance; Disposal And Recycling - Scheppach AB1500MAX Manuel D'utilisation

Starting the equipment

Using the chisel Fig. 2
• Clean the tool before fitting it and apply a thin coating
of grease to the tool shaft.
• Pull back the SDS MAX chuck lock (4) as far as pos-
sible. Insert the chisel as far as possible and turn it
until it locks.
• Release the SDS MAX chuck lock. It should only be
possible to move the chisel in the drill chuck by ap-
proximately 1 cm forwards or backwards.
• Check the lock by pulling the tool.
Removing the tool
To remove the tool, proceed in reverse order.
Turn the tool Fig. 3
To turn the tool into the correct position, the rear
unlocking ring (a) must be pulled and held. After this
the tool can be rotated to the desired position. To fix the
position release the release ring (a) and insure that it is
reliably locked.
Additional handle Fig. 2
For safety reasons you must only use the demolition
hammer with the additional handle.
The additional handle (3) enables you to achieve better
stability whilst using the demolition hammer.
For safety reasons the machine must not be used with-
out the additional handle (3).
The additional handle can be turned into any required
position. Undo the lock of the additional handle (3) by
turning the handle (3) counterclockwise. Then turn the
handle (3) into the most comfortable working position
and tighten the handle (3) by turning it clockwise.
Operation / Work instructions
Caution! For your safety, the machine must be held
only at the two handles (1 and 3, Figure 1)!
This will avoid the danger of an electric shock through
contact of lines during chiselling.
Switching on / off (Fig. 4)
This power tool works with torque switching.
Warning! Hold power tool safely on the main and ad-
ditional handle! Press until the power button! Otherwise
there is a risk of injury!
Hold power tool safely in vertical position on the main
and additional handle.
To switch on: Press the control switch (2).
To switch off: Release the control switch (2).
• For continuous operation, press the on/off switch (2)
and the locking button (b) on the handle at the same
time.
• To switch off continuous operation, press the on/off
switch (2) and then release it again.
Always keep the chiselling tools sharp.
Note:
– Work only at low pressure when chiselling
– Excessive pressure loads the motor unnecessarily.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
– Sharpen the chisels in time and replace, if necessary.
Replacing the power cable
If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its aftersales
service or similarly trained personnel to avoid danger.

Cleaning and maintenance

Always pull out the mains power plug before starting
any cleaning work.
Cleaning
• Keep all safety devices, air vents and the motor hous-
ing free of dirt and dust as far as possible. Wipe the
equipment with a clean cloth or blow it with com-
pressed air at low pressure.
• We recommend that you clean the device immediately
each time you have finished using it.
• Clean the equipment regularly with a moist cloth and
some soft soap. Do not use cleaning agents or sol-
vents; these could attack the plastic parts of the equip-
ment. Ensure that no water can seep into the device.
Carbon brushes
In case of excessive sparking, have the carbon brushes
checked only by a qualified electrician. Important! The
carbon brushes should not be replaced by anyone but
a qualified electrician.
Maintenance
There are no parts inside the equipment which require
additional maintenance.

Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material and
can therefore be reused or can be returned to the raw
material system.
The unit and its accessories are made of various types
of material, such as metal and plastic. Defective com-
ponents must be disposed of as special waste. Ask your
dealer or your local council.
Storage
Store the equipment and accessories out of children's
reach in a dark and dry place at above freezing tempera-
ture. The ideal storage temperature is between 5 and
30 °C. Store the electric tool in its original packaging.
15 І 48