Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
SPECIFICATIONS
Maximum Output Power
Full Bandwidth Power
Speaker Impedance
Tone Action
Preout Level/Load (USB)
Preout Impedance
Operating Voltage
Maximum Current Consumption
Operational Temperature Range
Installation Size (W × H × D)
Weight
Subject to change without notice.
50 W × 4
22 W × 4 (at less than 1 % THD)
4 Ω — 8 Ω
Band 1:
62.5 Hz ±9 dB
Band 2:
100 Hz ±9 dB
Band 3:
160 Hz ±9 dB
Band 4:
250 Hz ±9 dB
Band 5:
400 Hz ±9 dB
Band 6:
630 Hz ±9 dB
Band 7:
1 kHz ±9 dB
Band 8:
1.6 kHz ±9 dB
Band 9:
2.5 kHz ±9 dB
Band 10:
4 kHz ±9 dB
Band 11:
6.3 kHz ±9 dB
Band 12:
10 kHz ±9 dB
Band 13:
16 kHz ±9 dB
: 4 000 mV/10 kΩ
/
/
2 500 mV/10 kΩ
≤ 600 Ω
14.4 V (10.5 V — 16 V allowable)
10 A
–10°C — +60°C
:
182 mm × 53 mm × 159 mm (7-3/16" × 2-1/16" × 6-1/4")
/
/
182 mm × 53 mm × 107 mm (7-3/16" × 2-1/16" × 4-3/16")
: 0.85 kg (1.87 lbs)
/
/
0.7 kg (1.54 lbs)
INSTALLATION / CONNECTION
Warning
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery's negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car
chassis or Ground wire (black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car's chassis again after installation.
Caution
• For safety's sake, leave wiring and mounting to professionals. Consult the
car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts
of this unit during and shortly after use of the unit. Metal parts such as the
heat sink and enclosure become hot.
• Do not connect the [ wires of speakers to the car chassis or Ground wire
(black), or connect them in parallel.
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect
Ignition wire (red) to the terminal on the vehicle's fuse box which provides
12 V DC power supply and is turned on and off by the ignition key.
:
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers,
etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching car's chassis,
then replace the old fuse with one that has the same rating.
Basic procedure
1
Remove the key from the ignition switch, then
disconnect the [ terminal of the car battery.
2
Connect the wires properly.
:
See Wiring connection. ( 33, 34)
3
Install the unit to your car.
See Installing the unit (in-dash mounting).
4
Connect the [ terminal of the car battery.
:
5
Press
to turn on the power.
6
Detach the faceplate and reset the unit within
5 seconds. ( 3)
31
ENGLISH
Publicité
Table des Matières
