During Use; For The Environment; Assembly And Installation (To Be Performed By The Installer); Assembly - Brink WTW Mode D'emploi

• The Brink WTW control should be placed at a
height of approximately 1.65 meters above the
floor;
• The Brink WTW control may not be covered, for
example, by a curtain or a cabinet;
• Consult paragraph 1.2 for environmental
requirements.

2.3 During use

Take note! Settings, which have not been described
in this user's manual, are intended for installers
approved by Brink Climate Systems. Do not change
these by yourself.
2.4 During use
Careful! Clean the screen with a soft cloth.
Careful! Never apply water and/or (cleaning) liquid to
the screen.

2.5 For the environment

Take note! The WTW control may not be removed
as unsorted urban waste, but should be treated
separately.
Take note! Make enquiries within your own region,
where the WTW control can be handed in when use
has been terminated. Do not throw away electrical
devices or parts, but check if (parts of) the WTW
control cannot be handed in, recycled or re-used.
3 Assembly and installation (to be performed
by the installer)
Assembly and installation should be performed by an installer
approved by Brink Climate Systems.

3.1 Assembly

You should perform the steps, described in paragraph 3.1.1
through paragraph 3.1.4, one by one, to assemble the WTW
control.
3.1.1 Disconnecting the operational module from the wall
bracket
Disconnect the operational module from the wall bracket.
Perform the following actions
• Carefully insert a flat screwdriver in the rectangular
opening at the bottom of the operational module (see
A)
• Slowly tilt the screwdriver downwards. The operational
module clicks loose and can be removed (see

3.1.2 Electrical connection

The following actions should be performed to connect the
WTW control electrically (see
• Feed the two-core wire (from the device to be
connected) through via opening at the back of the wall
bracket.
4 :
B)
4
5
):
• Check that the cables' ends have been stripped in the
correct manner. If this is not the case, do so.
• Screw the cable to the terminal No. 1 and No. 2.
Consult the installation instructions of the device to
be connected, for more information on the correct
connection.

3.1.3 Mounting the wall bracket

The wall bracket can be attached to a wall box (Ø 55 mm) or
can be directly mounted on the wall with screws and plugs.
• Screw the wall bracket onto the wall in the correct
position. Here one must use the mounting holes in the
wall bracket (see
Take note! Consult paragraph 2.2 for more
information on placing the WTW control.
3.1.4 Replacing the operational module in the wall
bracket
Place the operational in the wall bracket mounted on the wall.
Perform the following actions for this
(see 7 ):
• Shift the pins at the top of the operational module to the
openings intended for them in the wall bracket.
• Turn the bottom of operational module towards the wall
bracket
Take note! The operational module should click
onto the wall bracket. Only then is a proper electrical
connection established.

3.2 Installation

3.2.1 Setting language

You can set the language in which the menus are presented.
Perform the following actions to set the language (see
• Press return
2
main screen
• Press . 'User Menu' opens
1
• Select 'User Settings' by turning
• Press . 'User Settings' opens
1
• Select 'Language' by turning
• Select a language by turning
Press to set the selected language
1
Take note! The names of the described menu items
will not correspond with this user manual's menu
items if the WTW control is set to a language other
than Dutch.

3.2.2 Setting time

4 You can set the time. The time is visible on the main screen
The WTW control only has 24 hour representation. Perform
the following actions to set the time (see
• Press return
2
main screen
• .Press . 'User Menu' opens
1
• Select 'User Settings' by turning
• Press . 'User Settings' opens
1
• Select 'Time' by turning
• Press . 'Time' opens
1
• Change the time by turning
7
)
6
as many times as necessary to get to the
1
1
1
1 ):
as many times as necessary to get to the
1
1
1
1 ):