During Use; For The Environment; Assembly And Installation (To Be Performed By The Installer); Assembly - Brink WTW control Mode D'emploi

The Brink WTW control should be placed at a height
The Brink WTW control may not be covered, for
example, by a curtain or a cabinet;
Consult paragraph
requirements.

2.3 During use

Take note! Settings, which have not been described
in this user's manual, are intended for installers appro-
ved by Brink Climate Systems. Do not change these
by yourself.
2.4 During use
Careful! Clean the screen with a soft cloth.
Careful! Never apply water and/or (cleaning) liquid to
the screen.

2.5 For the environment

Take note! The WTW control may not be remo-
ved as unsorted urban waste, but should be treated
separately.
Take note! Make enquiries within your own region,
where the WTW control can be handed in when use
has been terminated. Do not throw away electrical
devices or parts, but check if (parts of) the WTW con-
trol cannot be handed in, recycled or re-used.
3 Assembly and installation (to be performed
by the installer)
Assembly and installation should be performed by an installer
approved by Brink Climate Systems.

3.1 Assembly

You should perform the steps, described in paragraph 3.1.1
through paragraph 3.1.4, one by one, to assemble the WTW
control.
3.1.1 Disconnecting the operational module from the wall
bracket
Disconnect the operational module from the wall bracket.
Perform the following actions
ning at the bottom of the operational module (see
Slowly tilt the screwdriver downwards. The operational
module clicks loose and can be removed (see

3.1.2 Electrical connection

The following actions should be performed to connect the
WTW control electrically (see
Feed the two-core wire (from the device to be connected)
through via opening at the back of the wall bracket.
Check that the cables' ends have been stripped in the
correct manner. If this is not the case, do so.
Screw the cable to the terminal No. 1 and No. 2. Consult
1.2 for environmental
4
:
4
4
B)
5
):
the installation instructions of the device to be connected,
for more information on the correct connection.

3.1.3 Mounting the wall bracket

The wall bracket can be attached to a wall box (Ø 55 mm) or
can be directly mounted on the wall with screws and plugs.
Screw the wall bracket onto the wall in the correct posi-
tion. Here one must use the mounting holes in the wall
bracket (see
6
Take note! Consult paragraph 2.2 for more informa-
tion on placing the WTW control.
3.1.4 Replacing the operational module in the wall
bracket
Place the operational in the wall bracket mounted on the wall.
Perform the following actions for this
7
(see ):
Shift the pins at the top of the operational module to the
openings intended for them in the wall bracket.
Turn the bottom of operational module towards the wall
bracket
Take note! The operational module should click onto
the wall bracket. Only then is a proper electrical con-
nection established.

3.2 Installation

3.2.1 Setting language

You can set the language in which the menus are presented.
Perform the following actions to set the language (see
Press return
2
main screen
Press . 'User Menu' opens
1
Select 'User Settings' by turning
Press . 'User Settings' opens
1
Select 'Language' by turning
Select a language by turning
Press to set the selected language
1
Take note! The names of the described menu items
will not correspond with this user manual's menu items
if the WTW control is set to a language other than
Dutch.

3.2.2 Setting time

You can set the time. The time is visible on the main screen
- The WTW control only has 24 hour representation. Perform
A) the following actions to set the time (see
Press return
2
main screen
.Press 1 . 'User Menu' opens
Select 'User Settings' by turning
Press . 'User Settings' opens
1
Select 'Time' by turning
Press . 'Time' opens
1
Change the time by turning
Press 1
Repeat the previous two steps for both the minutes and
seconds
7
).
as many times as necessary to get to the
1
1
1
1 ):
as many times as necessary to get to the
1
1
1
1
):