Schumacher Electric XPF400 Manuel D'utilisation page 6

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

USING THE USB PORT
(Models XPF500, XPF750 and XPF750C)
The USB port provides up to 2A at 5V DC.
1. Ensure the battery clamps are securely
clipped on the storage holders.
2. Turn the Instant Power ON.
3. Plug your device into the USB port.
4. Turn the USB device on.
5. When finished using the USB port,
turn the switch to the OFF position.
6. Charge the Instant Power.
USING THE WORK LIGHT
The work light is controlled by an ON/OFF
switch located on the front of the Instant
Power. Make sure the lamp is turned OFF
when the unit is being recharged or stored.
The lamp is efficient and will operate up to
100 hours on a full charge.
Position the Instant Power on a flat, stable
surface near the intended work area.
Ensure the battery clips are securely
clipped on the storage holders.
POWERING A 12V DC DEVICE
The Instant Power is a power source for
all 12V DC accessories that are equipped
with a 12V accessory plug. Use it for power
outages and fishing or camping trips.
NOTE: Do not power a 12V device with the
Instant Power while charging the internal
battery.
1. Make sure the device to be powered
is OFF before inserting the 12V DC
accessory plug into the 12V DC
accessory outlet.
2. Open the protective cover of the DC
power outlet on the Instant Power.
3. Plug the 12V DC device into the DC
power outlet and turn on the 12V DC
device (if required).
4. When finished, turn off the DC device
(if required) and unplug from the DC
power outlet.
CAUTION: Do not use the Instant Power
to run appliances that draw more than
15A DC.
NOTE: Extended operation of a 12V DC
device may result in excessive battery
drain. Recharge the Instant Power
immediately after unplugging the 12V
DC device.
Estimated run-times
APPLIANCE
TYPE
WATTAGE
Cell phone
Fluorescent
light
Radios, fans
Depth finder
Camcorder
Electrical
tool
Electric
cooler
Car vacuum,
air compressor 80 watts
NOTE: Actual time may vary. Times are based on the
internal battery being fully charged.
USING THE AIR COMPRESSOR
(Model XPF750C only)
WARNING. Read the instructions of the
product being inflated before using the
compressor. Avoid overinflation; do not
exceed the manufacturer's recommended
pressures. Do not leave the air
compressor unattended during use.
NOTE: Wrap cleats are provided for
convenient storage of the air compressor
hose. Wrap the hose around these cleats
when the hose is not in use.
1. Ensure the battery clips are securely
on the storage holders.
2. Remove the air compressor hose
from the storage cleats on the back of
the Instant Power. Install adapters as
necessary.
3. Attach the air compressor hose to the
product or accessory to be inflated by
flipping down the lever.
4. Toggle the Compressor Switch up
to the ON position and inflate the
product.
5. When the product is inflated to
the proper air pressure (using the
air compressor gauge), toggle the
Compressor Switch down to the OFF
position and remove the hose.
6. Do not run for more than 10 minutes
maximum at a time. Allow the Instant
Power to cool down for 10 minutes
before using again.
• 6 •
EST
XPF400
XPF500
4 watts
13 hrs
19 hrs
4 watts
15 hrs
21 hrs
9 watts
6.7 hrs
9.3 hrs
9 watts
6.7 hrs
9.3 hrs
15 watts
4 hrs
5.6 hrs
24 watts
2.5 hrs
3.5 hrs
48 watts
1.3 hrs
1.8 hrs
0.8 hrs
1.1 hrs
XPF750,
XPF750C
34 hrs
34 hrs
14 hrs
14 hrs
7 hrs
5 hrs
2 hrs
1.8 hrs

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Xpf500Xpf750Xpf750cInstant power xpf750Instant power xpf750c

Table des Matières