EINHELL RT-SM 430 U Mode D'emploi D'origine page 22

Anleitung_RT_SM_430_U_SPK1:_
GB
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 61029.
Vibration emission value a = 1,148 m/s
h
K uncertainty = 1,5 m/s 2
Warning!
The specified vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equipment
is used and may exceed the specified value in
exceptional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
n
order.
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
n
necessary.
Switch the appliance off when it is not in use.
n
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
1. Lung damage if no suitable protective dust mask
is used.
2. Damage to hearing if no suitable ear protection is
used.
22
21.03.2012 9:33 Uhr Seite 22
3. Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or
is not properly guided and maintained.
Idle speed
6. Before starting the equipment
98,5 dB(A)
3 dB
6.1 General
111,5 dB(A) The machine must be firmly mounted in working
n
position, e.g. on a workbench, the base frame
3 dB
supplied with the machine, or similar.
All the covers and safety devices have to be
n
properly fitted before the machine is switched on.
It must be possible for the saw blade to run
n
freely.
When working with wood that has been
n
processed before, watch out for foreign bodies
such as nails or screws etc.
2
Before you actuate the On/Off switch, make sure
n
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
n
supply, make sure the data on the rating plate is
the same as that for your mains.
6.2 Assembling the saw (Fig. 1-3; 6)
To adjust the turntable (17), loosen the locking
n
grip (14) by approx. 2 turns, which frees the
turntable (17).
Press the locking lever (13), turn the turntable (17)
n
and scale pointer (15) to the desired angular
setting on the dial (16) and lock into place with
the locking grip (14). The saw has locking
positions at angular positions of -45°, -30°, -22,5°,
-15°, 0°, 15°, 22,5°, 30°, 45° and 60° at which the
locking lever can be engaged.
To release the saw from its position at the bottom,
n
pull the locking pin (27) out of the motor mounting
while pressing down lightly on the machine head
(4). Turn the locking pin (27) through 90° before
you release it so that the saw remains released.
Swing the machine head (4) up until the release
n
lever (3) latches into place.
The clamping device (8) can be fitted on either the
n
left or right of the fixed saw bench (18).
Undo the locking screws for the workpiece
n
support (30).
Guide the roller support with limit stop (9) over
n
one of the holding bars for the roller support (10)
and secure it to the fixed saw bench (18),
tightening the appropriate locking screw (30) (Fig.
6).
Fit the second holding bar for the roller support
n
(10) on the opposite side of the saw and secure it
with the appropriate locking screw (30).
When the locking screw (22) is loosened, you can
n