Ryobi P731 Manuel D'utilisation page 7

NOTICE:
Always leave low pressure hose free of obstructions and
with pinch valve adaptor off when not in use. Overheating
could occur low pressure hose is blocked.
DEFLATING WITH THE LOW PRESSURE HOSE
See Figure 7, page 11.
The low pressure hose, when placed in the deflator, can be
used to remove air from inflated items.
 Place the hose inside the deflator.
 Press the low pressure (I) switch to start deflating.
 When the item has been deflated, turn the switch off.
 Remove the hose by pulling if from the deflator.
 Store the hose in hose wrap on the left side of the product.
INFLATING WITH THE HIGH PRESSURE
HOSE
See Figure 8, page 11.
The air chuck on the high pressure hose can be used without
adaptors to inflate tires or with any application that has a
valve stem that fits the air chuck opening.
NOTE: When inflating items of 10 PSI or less, inflate in short
bursts and check after each burst by feel or with a calibrated
measuring device to determine accurate pressure.
 Press mode button to activate.
 Set desired pressure.
 Place air chuck on valve stem and lock in place.
 Press the high pressure (II) switch to start inflating.
 When the desired pressure is reached, turn the switch
off.
 Remove the hose and store in hose wrap on the right side
of the product.
 Press and hold the mode button to deactivate the display.
NOTE: Stand 10 feet away from item being inflated.
INFLATING WITH THE HIGH PRESSURE AIR
HOSE AND ACCESSORIES
See Figure 9 - 12, pages 11 - 12.
The high pressure air hose can be used with the provided
adaptors to inflate a variety of items.
 To install accessory: insert adaptor (or needle) into air
chuck and push air chuck clamp down until it locks into
place. Inflate to desired pressure.
 Remove accessory by lifting air chuck clamp up and
pulling the adaptor (or needle) from air chuck.
OPERATION
INFLATING MANUALLY FOR HIGH AND LOW
PRESSURE APPLICATIONS
 Connect either high or low pressure hose to item to be
inflated.
 Depress power switch to proper switch (low or high pres-
sure) until desired pressure is reached.
NOTE: Stand 10 feet away from item being inflated.
 Turn off power switch.
ACCESSORIES
See Figures 10 - 12, page 12.
The supplied accessories perform a variety of functions.
The tapered adaptor can be used on smaller pinch valves
to inflate items like floats and children's toys, which usually
require the user to inflate them by blowing air into them. The
sport ball needle can be used to inflate any type of sports ball
or any other item that requires an inflation sport ball needle.
NOTE: When inflating items of 10 PSI or less, inflate in short
bursts and check after each burst by feel or with a calibrated
measuring device to determine accurate pressure.
To use the sport ball needle:
 Insert sport ball needle into sports ball valve and inflate.
 Remove sport ball needle after inflation.
NOTE: Pressure required for most sports balls is too low for
accurate reading on gauge.
The Presta valve adaptor can be used for Presta valve stems
as described below. Before inflating a tire with a Presta
valve, loosen the locking nut on the valve stem to inflate.
Once inflation is complete, tighten the locking nut to seal
the tire valve.
To use the Presta valve adaptor:
 Loosen Presta valve locking nut.
 Thread Presta valve adaptor onto valve stem with larger
open end toward wheel.
 Position the air chuck clamp in the unlock position.
 Clamp the end of the air chuck down onto the Presta
valve adaptor by pressing air chuck clamp down until it
locks into place.
 After inflation, remove air chuck and tighten locking nut.
ACCESSORIES STORAGE
See Figure 13, page 12.
When not in use, adaptors and needles provided with the
inflator can be placed in the storage area located on the
right side of the tool.
HOSE STORAGE
See Figures 13 - 14, page 12.
When not in use, the hoses provided with the inflator can
be placed in the storage areas located on both sides of the
inflator.
7 — English