Télécharger Imprimer la page

Amana ASD2524VES02 Mode D'emploi page 11

Publicité

New installation?
Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice
production.
Ice stuck in the delivery chute? Use a plastic utensil to clear
the delivery chute.
Has the wrong ice been added to the bin? Use only cubes
produced
by the current ice maker.
Has the ice melted around the auger (metal spiral} in the
ice bin? Empty the ice container. Use warm water to melt the
ice if necessary.
Cut Hazard
Use a sturdy glass when dispensing
ice.
Failure to do so can result in cuts.
Is the ice dispenser stalling while dispensing "crushed"
ice? Change the ice button from "crushed" to "cubed." If
cubed ice dispenses correctly, depress the button for
"crushed"
ice and begin dispensing
again.
Has the dispenser arm been held in too long? Ice will stop
dispensing when the arm is held in too long. Wait 3 minutes
for dispenser motor to reset before using again.
The water dispenser
will not operate properly
Freezer door closed completely? Close the door firmly. If it
does not close completely, see "The doors will not close
completely."
Refrigerator
connected
to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
Is the water pressure
at least 30 psi (207 kPa)? The water
pressure to the home determines the flow from the dispenser.
See "Water Supply Requirements."
Kink in the home water source line? Straighten the water
source line.
New installation?
Flush and fill the water system.
Water filter installed
on the refrigerator?
The filter may be
clogged or incorrectly installed.
Is a reverse osmosis water filtration
system connected
to
your cold water supply?
See "Water Supply Requirements"
in either the Installation Instructions or the Use & Care Guide.
The dispenser
water is not cool enough
NOTE: Water from the dispenser is chilled to only 50°F (10°C).
New installation?
Allow 24 hours after installation for the
water supply to cool completely.
Recently
dispensed
large amount of water? Allow
24 hours for water supply to cool completely.
Water not been recently dispensed?
The first glass of water
may not be cool. Discard the first glass of water.
Refrigerator connected to a cold water pipe? Make sure
the refrigerator is connected to a cold water pipe. See "Water
Supply Requirements."
ACCESSORIES
To order replacement filters, call 1-800-442-9991
and ask for the
appropriate
part number listed below or contact your authorized
Amana dealer. In Canada, call 1-800-807-6777.
Stainless
Steel Cleaner and Polish:
Order Part #4396095
Standard
Filter:
Order Part #4396841 (T2RFWG2)
In Canada, Order Part #4396841B (T2RFWG2)
WATER FILTER CERTIFICATIONS
Tradelnark/Model
Designation
X'Vhhl
F )o]
Deluxe
TtWG2
Whirlpool
DeluxeTIWG2L
Kl[chenAid
DelaxeTl
WG?
KlmhenAld
DeluxeT1WG2L
ManuNeturor:
Wlurlpool
Corlx)rauon
State of California
Department
of Health Services
Water Treatment Device
CertificateNumber
05- 1702
Date Issued:
April 6, 2005
Date Revised:
September
7, 21X)5
Rel_lacement
Elements
o-DIcblorobenzene
Toxaphene
Water is leaking
from the dispenser
NOTE: One or two drops of water after dispensing
is normal.
Glass not being held under the dispenser
long enough?
Hold the glass under the dispenser 2 to 3 seconds after
releasing the dispenser lever.
New installation?
Flush the water system. See "Prepare the
Water System" or "Water and Ice Dispensers."
Recently
changed water filter? Flush the water system. See
"Prepare the Water System" or "Water and Ice Dispensers."
Rated Service
Capacity:
2/Xlgals
RatedServiceFtow:
05gpm
Conditions
of Certlfic_ttion:
Do not use wi(h wate_ (hat is microbiologically
unsale or of unknown
quail/y,
without
adequate
disinfection
befute
or
after me system
11

Publicité

loading