Machine Specifications; Technical Data; Noise Emission; Dust Emission - Jet Tools JTS-600XL Mode D'emploi

The type and condition of the
sawblade is important in keeping the
noise level as low as possible.
This does not negate the fact that
extra safety equipment such as ear
protection must be used.

4. Machine specifications

4.1 Technical data

Machine Table
Right extension table
Rear extension table
Sliding table size 1600x240 mm
Max. travel of sliding table
Max. length of cut
Sawblade diameter
Blade bore diameter
Blade speed n
0
Cutting height at 90°/45°
Tilting range of blade
Max. width of rip cut
Dust port diameter
Weight
Mains ~230V, L/N/PE, 50Hz
Motor output power 1,5kW (2HP) S1
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Mains ~400V, 3L/PE, 50Hz
Motor output power 1,5 kW (2 HP) S1
Reference current
Extension cord (H07RN-F): 4x1,5mm²
Installation fuse protection

4.2 Noise emission

Determined according to EN 1870-1
(Inspection tolerance 4 dB)
Workpiece plywood 16mm:
Acoustic power level
(according to EN ISO 3746):
Idling LwA
Operating LwA 101,8 dB (A)
Acoustic pressure level
(according to EN ISO 11202):
Idling LpA
Operating LpA
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
This information is intended to allow
the user to make a better estimation of
the hazards and risks involved.

4.3 Dust emission

The circular saw has been dust
emission evaluated.
At an air velocity of 20m/sec on the
dust port dia. 100mm:
Vacuum pressure
Volume flow
The TRK-value of 2 mg/m
exceeded.
4.4 Content of delivery
Machine stand
800x350 mm
Sliding table
800x270 mm
Sliding table support legs
415x350mm
Crosscut table
Crosscut fence
Telescopic arm
1700 mm
Rare extension table
1600 mm
Right extension table
max 250 mm
Rip fence with dual fence profile
30 mm
Rip fence support bar
4000 rpm
Saw guard
Sawblade 250mm
80/54 mm
Dust connection hose and Y-adapter
90°- 45°
Hose tye
610 mm
Push stick
100mm
Operating tools
170 kg
Assembly bag
Operating manual
Spare parts list
11 A
16A

4.5 Description of machine

4.7 A
16A
98,2 dB (A)
A......Crosscut fence
B.....Pull out lock knob
C....Crosscut stop
84,2 dB (A)
88,5 dB (A)
D.....Crosscut table
E.....Sliding table
F.....Raving knife
G.....Saw guard
H....Dust connection hose
I.....Rip fence
J......Telescopic arm
K....Front cabinet cover
850Pa
565 m³/h
3
is not
Fig 1
5
L....On/ Off switch
M....Blade tilt lock
N....Blade rise handwheel
O....Sliding table support leg
P....Sliding table lock
Q....Blade tilt handwheel
R....Rip fence micro adjustment

5. Transport and start up

5.1 Transport and installation

For transport to the desired location
use a forklift or hand trolley. Make
sure the machine does not tip or fall
off during transport.
The machine is designed to operate in
closed rooms and must be placed
stable on firm and levelled ground.
The machine must be levelled in both
directions to assure good sliding
motion of the sliding table.
If possible, the machine must be
placed on rubber plates which act as
shock absorbers and reduce the noise
level.
For packing reasons the machine is
not completely assembled.

5.2 Assembly

If you notice any transport damage
while unpacking, notify your supplier
immediately. Do not operate the
machine!
Dispose of the packing in an
environmentally friendly manner.
Clean all rust protected surfaces with
a mild solvent.
Mounting table extensions
Attach rear extension table (A, Fig 2)
to the machine table with hex head
screws and washers.
Attach right extension table (B) to the
machine table with hex head screws
and washers.
Put table surfaces in level to the main
table.
Use the rip fence profile to check and
the grub screws (C) to adjust.