Publicité
Liens rapides
H-1222, H-2484
96" PACKING TABLES
TOOLS NEEDED
Phillips Head
7/16" Wrench
Screwdriver
Flat Head
Screwdriver
Hardware Kit
1/4"-20 x 5/8" Bolt x 20
Lock Washer x 20
Locking Tab x 6
#
DESCRIPTION
1
Adjustable Foot
2
Leg
3
Stringer
4
Lower Shelf
5
Tabletop
LEGS AND FRAME ASSEMBLY
1.
Insert adjustable feet (1) into legs (2) and slide into
place at desired height.
NOTE: If desired, insert locking tabs through
legs and adjustable feet to lock feet into place.
2. Place legs (2) in upright position. Legs should be
placed approximately 45" apart.
PAGE 1 OF 6
1-800-295-5510
uline.com
3/8" Wrench
10 mm Wrench
(For Non-Steel Top Assembly)
1/4"-20 Nut x 20
#14 x 3/4" Wood Screw x 24
QTY
6
3
2
2
1
PARTS
4
2
If you purchased L-Shaped Workstation or
Deluxe Workstation, use instructions packaged
with H-5777 uprights.
ASSEMBLY
3. Attach stringers (3) to table legs using center six
holes in back legs. Fasten with 12 bolts, lock washers
and nuts, but do not fully tighten. (See Figure 1)
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
5
3
1
Figure 1
0125 IH-1222
Publicité
Manuels Connexes pour Uline H-1222
Sommaire des Matières pour Uline H-1222
- Page 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-1222, H-2484 1-800-295-5510 uline.com 96" PACKING TABLES TOOLS NEEDED Phillips Head 7/16" Wrench 3/8" Wrench Screwdriver 10 mm Wrench (For Non-Steel Top Assembly) Flat Head Screwdriver PARTS Hardware Kit 1/4"-20 x 5/8"...
- Page 2 2. Attach center leg using four 1/4"-20 x 5/8" bolts, four lock washers and four 1/4"-20 nuts. NOTE: Center of table does not include threaded inserts. 3. Set bench assembly upright and recheck all bolts for tightness. Figure 4 1-800-295-5510 uline.com PAGE 2 OF 6 0125 IH-1222...
- Page 3 H-1222, H-2484 800-295-5510 uline.mx MESAS DE TRABAJO DE 96" HERRAMIENTAS NECESARIAS Desarmador Llave de 7/16" Llave de 3/8" de Cruz Llave de 10 mm (Para Ensamblar Cubiertas que no Sean de Acero) Desarmador Plano PARTES Kit de Accesorios 20 Pernos de 1/4"-20 x 5/8"...
- Page 4 1/4"-20 x 5/8", cuatro rondanas de seguridad y cuatro tuercas de 1/4"-20. NOTA: El centro de la mesa no incluye insertos roscados. 3. Enderece el ensamble y revise de nuevo que todos los pernos estén apretados. Diagrama 4 800-295-5510 uline.mx PAGE 4 OF 6 0125 IH-1222...
- Page 5 H-1222, H-2484 1 800 295-5510 uline.ca TABLES D'EMBALLAGE DE 96 PO OUTILS REQUIS Tournevis Clé de 7/16 po Clé de 3/8 po cruciforme Clé de 10 mm (pour le montage de dessus de table autre qu'en acier) Tournevis à tête plate PIÈCES...
- Page 6 REMARQUE : La partie centrale de la table ne dispose pas de sections filetées. 3. Placez la table à l'endroit, puis vérifiez que tous les boulons sont serrés. Figure 4 1 800 295-5510 uline.ca PAGE 6 OF 6 0125 IH-1222...