Publicité
Liens rapides
SPECS
Size: 4.3" x 4.3" x 8.85" (10.9 x 10.9 x 22.5 cm)
Input: 4.4-6.0 V 1 A
Battery Capacity: 1500 mAh
Voltage: 2.5 V / 3 V / 3.5 V / 4.2 V
Charging: USB-C
Atomizer Resistance: 1
Auto-filling
Triple quartz coil
KIT INCLUDES
1x Pulsar Sipper base
1x Glass bubbler cup
1x Mouthpiece
1x Airflow valve
1x Airflow silicone
1x Atomizer/cartridge cover
1x Wax atomizer
1x 510 connection
1x Dab tool/poker
1x USB-C charging cable
ASSEMBLY
Remove the atomizer/cartridge cover from the Sipper base and screw the wax atomizer or cartridge (not included)
into the 510 connection then replace the cover. The light around the touchpad will flash the current voltage to show
a successful connection has been made if the Sipper is already on. Put the two pieces of the airflow valve together
before inserting it into the bottom of the bubbler cup. Now place the bubbler cup on top of the cover, lightly
pressing down so there is a good fit. This should not require a lot of pressure.
LOADING
Remove the bubbler cup from the cover and then remove the cover from the base. With the wax atomizer connect-
ed, load a small amount of concentrate into the atomizer. About a half grain of rice is all that is needed; be sure not
to overfill the atomizer. Then replace the cover and sit the bubbler cup back on top.
ATTENTION! Do not touch the coils with metal dab tools while the Sipper is working.
CHANGE VOLTAGE SETTINGS
Press the touchpad 3 times to select your voltage. Once you have your voltage selected press and hold the
touchpad.
Voltages:
Yellow - 2.5 V
Blue - 3 V
USAGE
Press the touchpad with the tip of your finger 5 times to turn on the Sipper, the light around the touchpad will flash
to let you know it is on and the battery life.
Green - 100% - 70%
Blue - 70% - 30%
Note: The Sipper will automatically turn off after 10 minutes of inactivity.
• Operating Wax Atomizer - With the Sipper turned on, press the touchpad 3 times to change your voltage. Once you
have your voltage selected, touch and hold the touchpad. You will hear the pump activate and see the vapor start
filling the lower bubbler cup. Be sure to not cover the carb hole in the bubbler cup while it is filling. Once the lower
bubbler cup is filled, cover the carb hole, pull the bubbler cup off the base, and inhale through the mouthpiece.
• Operating 510 Cartridge - Remove the wax atomizer and unscrew the 510 connection before inserting a 0.5 mL or
1 mL 510 cartridge to the 510 connection, then screw the 510 connection back into the base. Replace the cover and
sit the bubbler cup back on top. Press the touchpad 5 times to turn on the Sipper, the light around the touchpad will
PAGE 1
INSTRUCTION
MANUAL
BUBBLER CUP
WAX
510
ATOMIZER
CONNECTION
Green - 3.5 V
Red - 4.2 V
Red - 30% - 0%
PulsarShop.com
LOWER
UPPER
BUBBLER CUP
CARB HOLE
AIRFLOW
VALVE
POWER
BUTTON/
TOUCHPAD
CHARGING
PORT
PU-0357-21
Publicité
Manuels Connexes pour Pulsar SIPPER
Sommaire des Matières pour Pulsar SIPPER
- Page 1 Red - 4.2 V USAGE Press the touchpad with the tip of your finger 5 times to turn on the Sipper, the light around the touchpad will flash to let you know it is on and the battery life. Green - 100% - 70%...
- Page 2 Try removing and reinstalling the wax atomizer to reset connection. Otherwise, replace with a new wax atomizer. Low Battery Indicator: When the battery is less than 5% the light will flash red 8 times and the Sipper will power off. Use the USB-C charging cable to recharge the Sipper until the touchpad light turns green.
- Page 3 Rouge - 4,2 V UTILISATION Appuyez du bout du doigt 5 fois sur la touche pour mettre le Sipper en marche. Le voyant qui l’entoure clignote pour indiquer la mise en marche et la durée de vie de la batterie.
- Page 4 Sinon, remplacez par un nouvel atomiseur. Indicateur de batterie faible: Lorsque la batterie est à moins de 5%, le voyant clignote 8 fois en rouge et le Sipper se désactive. Utilisez le câble de recharge USB-C pour recharger le Sipper Jusqu’à ce que le voyant de la touche devienne vert.