Télécharger Imprimer la page
LEGRAND SANUS BSA-OWCM301 Instructions D'installation
LEGRAND SANUS BSA-OWCM301 Instructions D'installation

LEGRAND SANUS BSA-OWCM301 Instructions D'installation

Couvre-fil d'ecran de televiseur plat

Publicité

Liens rapides

FLAT SCREEN TV CORD COVER
COUVRE-FIL D'ÉCRAN DE TÉLÉVISEUR PLAT
PROTECTOR DE CABLES DE TV DE PANTALLA PLANA
Tools Needed:
Materials Provided:
Before Installation:
Peut être peint
Se puede pintar
Outils requis:
Matériel fourni:
Avant l'installation:
Herramientas requeridas:
Materiales provistos:
Antes de la instalación:
I N S T A L L A T I O N
I N S T R U C T I O N S
I N S T R U C C I O N E S
BEFORE INSTALLATION
Tape Measure, Level, Pencil, Phillips Screwdriver, Hand or Hacksaw
Flat Screen TV Cord Cover (Base & Cover), 6 Mounting Anchors & Screws
For installation using the mounting hardware provided, locate the Flat Screen TV Cord Cover between
wall studs. Allow 1" [25mm] clearance between the wall surface and the back side of the flat screen
panel for the Flat Screen TV Cord Cover installation.
NOTE: The wall anchors provided with the kit cannot be used over wall studs.
Ruban à mesurer, niveau, crayon, tournevis Phillips, égoïne et scie à métaux
Couvre-fil d'écran de téléviseur plat (base et couvercle), 6 fixations et vis de montage
Pour une installation avec le matériel de montage fourni, placez le couvre-fil d'écran de téléviseur plat
entre les montants du mur. Laissez un dégagement de 1 po [25 mm] entre la surface du mur et
l'arrière du panneau de l'écran plat pour installer le couvre-fil d'écran de téléviseur plat.
NOTE : Les fixations murales fournies avec la trousse ne peuvent être utilisées sur les montants du mur.
Cinta métrica, nivel, lápiz, destornillador Phillips, serrucho o segueta
Protector de cables de TV de pantalla plana (Base y cubierta), 6 anclas de montaje y tornillos.
Para instalar usando los accesorios de montaje provistos, sitúe el protector de cables de TV de
pantalla plana entre los montantes de la pared. Deje 1" [25mm] de espacio libre entre la superficie de
la pared y la parte de posterior del panel de la pantalla plana para la instalación del protector de cables
de TV de pantalla plana.
NOTA: Las anclas de pared provistas con el kit no se pueden usar sobre los montantes de pared.
D ' I N S T A L L A T I O N
I N S T R U C T I O N S
D E
I N S T A L A C I Ó N
AFTER INSTALLTION

Publicité

loading

Sommaire des Matières pour LEGRAND SANUS BSA-OWCM301

  • Page 1 FLAT SCREEN TV CORD COVER COUVRE-FIL D'ÉCRAN DE TÉLÉVISEUR PLAT PROTECTOR DE CABLES DE TV DE PANTALLA PLANA Tools Needed: Tape Measure, Level, Pencil, Phillips Screwdriver, Hand or Hacksaw Materials Provided: Flat Screen TV Cord Cover (Base & Cover), 6 Mounting Anchors & Screws Before Installation: For installation using the mounting hardware provided, locate the Flat Screen TV Cord Cover between wall studs.
  • Page 2 1. Measure the width of the flat screen panel to determine and mark 2. Using a level, mark a plumb line that extends under the flat screen the center location of the Flat Screen TV Cord Cover. panel. This line will be used to help align the base of the Flat Screen TV Cord Cover for the horizontal drop.
  • Page 3 6. Mark the top two holes, the bottom two holes and two more holes 7. Using a Phillips screwdriver, push one of the anchors into the drywall off-set closest to the center of base. until it reaches the start of the thread. Push and turn anchor into drywall until it is tight and flush to surface.
  • Page 4 © Copyright 2007 Wiremold / Legrand All Rights Reserved 6436 City West Parkway 340765 Rev.C 0107 ©2023 Legrand AV Inc. All rights reserved. Sanus is a brand of Legrand. Eden Prairie, MN 55344 USA 05/2023 SANUS and the SANUS logo are registered trademarks of Legrand...