TP-Link Tapo C520WS V2 Guide De Démarrage Rapide

Quick Start Guide
Outdoor Pan/Tilt Security Wi-Fi Camera
Setup Video
Scan QR code or visit
https://www.tp-link.com/support/setup-video/
#cloud-cameras
*Images may differ from actual products.
02
/ Mount Your Camera
Option 1: Wall Mount
1. Affix the Camera and Bracket
Route the camera power
cord and Ethernet cable
through the opening of the
bracket. Use two bracket
screws to affix the bracket
and camera.
2. Drill Holes
Stick the mounting template to
the desired mounting place.
Drill four screw holes according
to the template.
3. Mount the Camera
Insert four mounting anchors
into the holes, then use the
mounting screws to affix the
camera and bracket over the
anchors.
Note: Adjust the antenna vertically
for the best Wi-Fi signal.
03
Install Waterproof Accessories
/
1. Install the Waterproof Seal for Power Connectors
Install the waterproof seal for the power connectors.
Male Power Waterproof Female Power
Connector Seal Connector
2. Install Waterproof Cable Attachments
Install the waterproof cable attachments for the network
interface. Make sure each part is securely attached and the
waterproof rings are flush to keep out water.
Appearance
1
2
4
3
5
Lens Reset
1 6
Open the silicone cover. While the camera is
powered on, use a pin to press and hold the
2 White Light LEDs
RESET button to reset the camera.
• Press and hold for 5s: Reset Wi-Fi settings only
3 IR LEDs
• Press and hold for 10s: Reset to factory settings
microSD Card Slot
7
4 System LED
Open the silicone cover and insert a microSD card.*
Initialize it on the Tapo app for local recording.
5 Microphone
*microSD card not included.
System LED Indication
Solid red
Starting up
Blinking red and green
Ready for setup
(for Wi-Fi setup)
Blinking red slowly
Connecting to Wi-Fi
(for Wi-Fi setup)
Solid amber Connected to Wi-Fi or wired network
Solid green Connected to the cloud
Blinking red quickly Camera resetting
Blinking green quickly Camera updating
01
/ Set Up Your Camera
1. Download App
Download the Tapo app from the App Store or Google Play,
and log in.
2. Power Up
Plug in the adapter to power up your camera.
7106511538 REV2.0.0
The camera is not waterproof when set on a table or shelf. Mount the camera via Option 1-3 when installing outdoors.
Option 2: Overhang Mount
1. Affix the Camera and Bracket
Route the camera power
cord and Ethernet cable
through the opening of the
bracket. Use two bracket
screws to affix the bracket
and camera.
2. Drill Holes
Φ=6 mm (15/64 in.)
Stick the mounting template to
the desired mounting place.
Drill four screw holes according
to the template.
3. Mount the Camera
Insert four mounting anchors
into the holes, then use the
mounting screws to affix the
camera and bracket over the
anchors.
Note: Adjust the antenna vertically
for the best Wi-Fi signal.
When the Ethernet port connects to a network device
Fix Nut Waterproof
Ring
1) Route the network cable through the following components in
order: fix nut, waterproof ring, and then the waterproof jacket.
2) Insert the waterproof ring into the waterproof jacket.
3) Fix the O-ring to the network interface of the camera and connect
the network cables.
4) Attach the network interface with the waterproof jacket, then twist
to lock. Rotate the fix nut to secure it to the waterproof jacket.
6 7
microSD
Visit https://www.tapo.com/support/
for technical support, the user guide, FAQs,
OR
Φ=6 mm (15/64 in.)
Waterproof O-ring
Network
Jacket
Interface
8 9
8 Speaker
9 Ethernet Port
Used to connect to a network
device by an Ethernet cable.
10 DC Power Connector
Need some help?
warranty & more
3. Set Up
Tap the button > Add Device in the app and select your
model. Follow the app instructions to set up your camera.
Option 3: Pole Mount
1. Affix the Camera and Bracket
Route the camera power
cord and Ethernet cable
through the opening of the
bracket. Use two bracket
screws to affix the bracket
and camera.
2. Mount the Camera
Mount the camera on the
pole using two
pole-mounting loops* (loop
width ≤ 12 mm).
*Pole-mounting loops are not
included.
Note: Adjust the antenna vertically
for the best Wi-Fi signal.
When the Ethernet port does not connect to a network
device
Fix Nut Waterproof Waterproof O-ring
Network
Ring + Plug Jacket
Interface
1) Insert the waterproof plug into the waterproof ring, then insert
them into the waterproof jacket.
2) Fix the O-ring to the network interface of the camera. Attach the
network interface with the waterproof jacket, then twist to lock.
Rotate the fix nut to secure it to the waterproof jacket.
Safety Information
• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended.
• Do not use the device where wireless devices are not allowed.
• Adapter shall be easily accessible.
• Use only power supplies which are provided by manufacturer
and in the original packing of this product. If you have any
questions, please don't hesitate to contact us.
• Keep the device away from fire or hot environments. DO NOT
immerse in water or any other liquid.
• Do not disassemble, repair or modify the product.
• Do not use the product if the casing has been broken. Danger of
electric shock.
• Never touch the product with wet hands.
• Do not place near automatically controlled devices such as fire
alarms. Radio waves emitted from this product may cause such
devices to malfunction resulting in an accident.
• Observe restrictions on using wireless products in fuel depots,
chemical plants or when blasting operations are in progress.
10
• Do not use liquid to clean the product. Only use a dry cloth.
• Never put metal objects inside the product. If a metal object
enters the product turn off the circuit breaker and contact an
authorised electrician.
• This product is not intended to be used when providing medical
care. Consult the manufacturer of any personal medical devices,
such as pacemakers or hearing aids to determine if they are
adequality shielded from external RF (radio frequency) energy.
• Do not use this product in health care facilities. Hospitals or
health care facilities may be using equipment that could be
sensitive to external RF energy.
• Do not place heavy objects on top of the product.
• When you leave the product unused for a long time unplug the
product from the power outlet.
• This product may interfere with other electronic products such
as TV, radios, personal computers, phones or other wireless
devices.
• Adapter should be used indoors where the ambient temperature
is lower than or equal to 40 ºC.
• Operating Temperature: -30 ºC ~ 60 ºC (-22 °F ~ 140 °F )
Please read and follow the above safety information when
operating the device. We cannot guarantee that no accidents or
damage will occur due to improper use of the device. Please use
this product with care and operate at your own risk.
©2024 TP-Link
My Home
Pole-mounting loops