Publicité
CARE AND MAINTENANCE
Detergents
• Use detergents designed for power washers. These
can be purchased online at our website www.
pressure washing from bottom
arblueclean.com. Hardware stores or home centers
also have power washer detergents for different
up for same reason.
cleaning projects. The cleaning solution should be
the consistency of water in order to prevent clogging
•
If a stain is particularly tough,
your detergent bottle and nozzle.
• This system applies detergent under low pressure.
it may be necessary to reapply
The cleaning power of the detergents is enhanced
when applied with low pressure and enough time is
the detergent and use a bristled
given to break down dirt and grime. The combination
of low pressure and chemical action is very effective
brush to scrub the stain.
and can be better than scrubbing if applied properly.
ALWAYS spray detergent on a dry surface. DO NOT
Subsequent power washing after
pre-soak area. Wetting the surface first dilutes
the detergent and reduces its cleaning ability. DO
brushing should successfully
NOT allow detergent to dry on surface. On vertical
surfaces being cleaned, apply detergent to lower
complete your cleaning job.
surfaces and work your way up to prevent detergent
from causing streaks in the dirt and grime. Rinse
detergent by pressure washing from bottom up for
same reason.
Cleaning Garden Hose Adapter
• If a stain is particularly tough, it may be necessary
•
The screens inside the clear
to reapply the detergent and use a bristled brush to
scrub the stain. Subsequent power washing after
garden hose adapter should be
brushing should successfully complete your cleaning
job.
cleaned periodically. Rinse it
Cleaning Garden Hose Adapter
with clean water, and then place
• The screens inside the clear garden hose adapter
should be cleaned periodically. Rinse it with clean
it back in the adapter.
water, and then place it back in the adapter.
Cleaning Nozzles
•
A clogged or partially clogged
nozzle can cause significant
reduction of water pressure
15ANR012 AR383S_1800PSI ENG-FR-SP.indd 13
coming out of the nozzle and/or
cause the unit to pulsate while
spraying.
•
Turn off the unit.
•
Turn off the water supply to the
unit.
•
Relieve any pressure trapped
in the hose by squeezing the
trigger 2-3 times, and then lock
the spray gun by pushing the
lock button from left to right.
14
All manuals and user guides at all-guides.com
Cleaning Nozzles
• A clogged or partially clogged nozzle can cause
significant reduction of water pressure coming out
• Remove the lance from the spray
of the nozzle and/or cause the unit to pulsate while
spraying.
gun
• Turn off the unit.
• Turn off the water supply to the unit.
• Using the nozzle tip cleaner
• Relieve any pressure trapped in the hose by
squeezing the trigger 2-3 times, and then lock the
provided (or an unfolded paper
spray gun by pushing the lock button from left to
right.
clip), insert the wire into the
• Remove the lance from the spray gun
• Using the nozzle tip cleaner provided (or an unfolded
nozzle hole and move back and
paper clip), insert the wire into the nozzle hole and
move back and forth until debris is dislodged.
forth until debris is dislodged.
• Tap quick connect end of lance on hard surface
several times
• Tap quick connect end of lance on
• Back flush water through the nozzles using garden
hose and highest pressure available (either standard
hard surface several times
water nozzle or use your thumb over the nozzle to
• Back flush water through the
create water pressure for back flush).
nozzles using garden hose and
highest pressure available (either
standard water nozzle or use your
thumb over the nozzle to create
water pressure for back flush).
13
16/12/17 下午2:28
Storage
•
When your pressure washing session
has been completed, turn off the
power switch located on the front
of the power washer. Unplug the
power cord from the outlet. Turn
off the water supply. Pull the trigger
on the spray gun 2-3 times to drain
out the excess water and to release
any remaining water pressure.
Disconnect the garden hose adapter
from the water inlet. DO NOT allow
the power washer to run with no
water flowing through it.
•
Remove detergent bottle and clean
completely. Residual chemical will
stick to the container and can
cause the detergent injector to clog
and not function properly.
PUMP SAVER
Pump Saver is a product that
protects and prolongs the life of the
pump. This will keep the internal
parts of the pump lubricated and
protected from freezing while
being stored in ALL climates. It
also assists with protection from
internal corrosion. The BE part # is:
85.490.046 (16oz. bottle).
Pump Saver Instructions
Follow the previous storage
instructions for your power washer.
To prevent staining, protect the
surface under the power washer from
any excess fluid. Wear eye protection
when using this product.
Turn unit off and disconnect the
gun before adding pump protector.
•
Remove high pressure hose
from spray gun.
•
Remove lance from the gun.
Place the gun in the holder on
the side. Lances are placed into
any of the slots in the back of
the unit. Make sure to discard
any remaining detergent from
the bottle. Flush the bottle and
nozzle head with fresh water
to prevent clogging.
•
Hook the power cord around
the L-shaped tabs on the right
side of the machine when
facing it.
Unscrew threaded top from bottle to
remove seal and reattach threaded
top to bottle. Remove black cap from
bottle.
1) Place top of pump saver bottle
onto the garden hose adapter
previously installed to pressure
washer inlet.
2) Secure pump saver bottle by
15
Publicité
