Publicité
EN
SAFETY INSTRUCTIONS
Warning: Read the manual carefully before use. Failure to follow the warnings and instructions may result in damage to the unit and/or
physical injury. Store the manual in a safe place for future reference.
• All electrical sockets must be earthed.
• No power cord should be used for transporting or fixing the equipment.
• Don't pull the power cord on the sharp edge and don't press the power cord.
• The power supply voltage must be the same as the voltage given on the model board.
• To avoid hazards, all installation and replacement of components can only be carried out by authorized customer service personnel.
• Electrical connections can only be performed by electrical professionals, and please comply with state regulations for this.
• The pump must be connected with a current type leakage current breaker which carry a rated leakage current of no more than 30 MA.
• Check the connection of the plug before running. If the wire is damaged, it must be replaced by the manufacturer, the agent or the relevant technical
personnel to avoid any danger.
• The device is suitable for children at eight or older. Children are not allowed to wash or maintain equipment without supervision.
• Liquid contamination may be caused by leakage of lubricating oil.
• The plug must have a supply voltage of 230V~ 50Hz.
• Do not use pumps when there is someone in the water.
• Before repairing, cleaning or maintaining the pump, disconnect it from the power supply.
Warning:
• Failure to follow the safety instructions can lead to electric shock.
• Do not repair the power cord if there is any external damage to the power cord or plug.
• The submersible pump is designed for pumping water (not drinking water) with a maximum temperature of 35°C. The pump must not be used for
pumping motor fuels, cleaning fluids, and other chemical products.
• Do not pump corrosive substances, flammable and explosive substances (such as gasoline, petroleum, nitro diluent), grease, oil, brine and toilet
equipment sewage, as well as low mobility mud sewage.
• This equipment is not suitable for continuous pumping operations.
TECHNICAL DATA
Model
NP1115
Input power
550 W
Max. pump height
9 m
Max. flow rate
17000 lt/h
Max. grain size
5 mm
Lowest suction level
1 mm
Cable length
10 m
INTENDED USE
This pump is used primarily as cellar pump. When installed in a shaft, the pump provides protection from flooding. The pump is used wherever water has to
be moved from one place to another.
INSTALLATION
The submersible pump is installed as follows:
• In a stationary position with fixed pipeline.
• In a stationary position with a flexible hose.
Attention: You should never install the pump by suspending it unsupported from its delivery pipe or power cable. The submersible pump must be suspended
from the specially provided handle or be placed on the bottom of the shaft. To guarantee that the pump works properly, the bottom of the shaft must be
kept free of sludge and dirt of all kinds. If the level of water sinks too far, any sludge in the shaft will dry out quickly and stop the pump from starting up. It
is necessary, therefore, to check the submersible motor pump regularly (by carrying out start-up tests). The floater is adjusted in a way that the pump can
immediately be started.
Note: The minimum dimensions of the pump shaft should be 60x60 cm, so that the float switch can move freely.
MAINS SUPPLY
• The submersible pump is equipped with a shockproof plug according to regulations. The pump is designed to be connected to a 230 V, 50 Hz safety socket.
• Make sure that the socket is sufficiently secured (min. 6 Amp) and is in excellent condition. Insert the plug into the socket and the pump is ready to go.
• Not using the right cable can be dangerous. When operating outdoors, use only the authorized and suitable extension cable which has sufficient wire cross-
section.
3
* The manufacturer reserves the right to make minor changes to product design and technical
specifications without prior notice unless these changes significantly affect the performance and
safety of the products. The parts described / illustrated in the pages of the manual that you hold in
your hands may also concern other models of the manufacturer's product line with similar features
and may not be included in the product you just acquired.
* To ensure the safety and reliability of the product and the warranty validity, all repair, inspection
or replacement work, including maintenance and special adjustments, must only be carried out by
technicians of the authorized service department of the manufacturer.
* Always use the product with the supplied equipment. Operation of the product with non-provided
equipment may cause malfunctions or even serious injury or death. The manufacturer and the
importer shall not be liable for injuries and damages resulting from the use of non-conforming
equipment.
WWW.NIKOLAOUTOOLS.COM
Publicité
