Publicité
Liens rapides
Publicité
Sommaire des Matières pour Yaohua Weighing System XK3190-DS3
- Page 1 XK3190-DS3 Weighing Display Controller（control system weighing indicator） Operation Command V 1.01...
- Page 2 Chapter 1 Technical Parameter Chapter 2 Installation I. Front and Back Functional Schematic Diagrams of Indicator II. Connection between Lload Cell and Indicator III. Connection between Printer and Indicator IV. Connection of Scoreboard V. Connection of Serial Communication Interface Chapter 3 Operation Method I.
- Page 3 X K 3 1 9 0 –DS3 Chapter 1 Technical Parameter 1. Model: XK3190-DS3 2. Interface of digital load cell(s): Interface mode: RS485 Transmission distance: ≤1000 meter Transmission speed: 9600 baud Signal power source: DC10V，≤400mA Interface capability: ≤16 digital load cell(s)
- Page 4 Calibration switch (Figure 2-2) Back) Function Schematic Diagram II. Connection between Load cell and Indicator XK3190-DS3 is a digital weighing indicator. Therefore, Shield it can only be connected with digital load cell (indicator). For easy indication, the product is called as load cell (indicator) for short.
- Page 5 X K 3 1 9 0 –DS3 2. Load cell interface of XK3190-DS3 adopts the interface mode of four-wire RS485 mode. Indicator Interface Pins Sensor (load cell) Interface Pins …… Color of Corresponding Wire Definition Connection Method Zhonghang Electronic Guangzhou Electrical...
- Page 6 X K 3 1 9 0 –DS3 interface《sharing with serial communication interface》). See Pins 9 and 10 for definition of its pins in Figure (2-5). Signal ground Connect the scoreboard Scoreboard RS233 output interface (Figure 2-5) Serial communication and scoreboard output interface signal back scheme of the machine...
- Page 7 Therefore, it shall be participated or guided by professional technician. Non-professionals are not allowed to connect the indicator. The indicator XK3190-DS3 is equipped with RS232/RS422 (optional)/RS485(optional) serial communication interface for communication purpose with computer. Communication interface is equipped with 15 core RS233 connector assembly (shared with scoreboard). See definition of pins 6, 7, and 8 (RS232) or 1, 2, 3, 4 and 8 (RS422/RS485) in Figure 2-5.
- Page 8 X K 3 1 9 0 –DS3 X byte Content and Note Xor checking （ Four lower bits 03(X0FF) Xor=2⊕3 Contents output by the indicator: X byte Content and Note 02(XON) Start No. of Address Command A: Hand shaking Command B: Input the gross weight Command C: Input the tare Command D: Input the net weight Press command to output corresponding data...
- Page 9 X K 3 1 9 0 –DS3 be ASCII code letter for sending, for example, Xor checking four higher bit is B. With 37h added, it is 42h, i.e. letter B in ASCII code for sending out. 3. Command list sent by host computer (set address of the indicator as 01): Content of Command Host computer sends out commands (hexadecimal) Category Command A Hand shaking...
- Page 10 X K 3 1 9 0 –DS3 I. Startup and Auto Startup Zero Setting Connect the AC power source or external battery and turn on the power to conduct stroke self-check of “9999999”~ “0000000” and then enter into weighing state automatically after this. During the process of stroke self-check, you may press any key to stop the self-check.
- Page 11 For weighing just article, one time of data saving may form a complete record. For recognizing and classifying three above situations, we make following agreement for XK3190-DS3: ▲ The vehicle no. shall be a number within the range of 00001～99999, i.e. 00000 cannot be kept as a real vehicle number.
- Page 12 X K 3 1 9 0 –DS3 as the tare weight and saved in the group of record. 6. When vehicle numbers are more than 1000, [Err 10] will be displayed on the indicator. A vehicle number or all contents recorded may be deleted in the way introduced in Chapter 11. VIII.
- Page 13 X K 3 1 9 0 –DS3 Step Operation Displayed content Note digit: 0 Unit of weight is kilogram 1 Unit of weight is ton; digit: 0 Do not use article number in data record 1 Use article number in data record;...
- Page 14 X K 3 1 9 0 –DS3 X. Inquiry Record All kinds of recorded contents in the indicator can be checked by using the key [Check] in different ways. See detailed operation ways as follows, 1. Check weighing record according to date (Table 4-4) Step Operation Displayed content...
- Page 15 X K 3 1 9 0 –DS3 Step Operation Displayed content Note Press [Check] [t**.**.**] Time (Hour/Minute) Press [Check] ***] Article No. Record of the second time Press [Check] [A *****] Gross Weight Press [Check] [t *****] Tare Press [Check] [n *****] Net Weight …...
- Page 16 X K 3 1 9 0 –DS3 Press [Check] [o *****] Press [Check] The second vehicle no. … … … [no nnn] Press [Check] [o *****] The last vehicle no. Press [Check] [ End ] Press [Check] Return to weighing displaying state (1) During the process of above operation, when the vehicle number is displayed, you may delete the vehicle number, its memorial tare and all weighing record of the vehicle number by pressing...
- Page 17 See information about setting of power saving in contents about parameter Y in print setting) XIV. Adjustment of Brightness XK3190-DS3 has 6 levels of brightness for adjustment. Press [Brightness] once to adjust the brightness to a higher level. When the brightness is adjusted to the highest level, the buzzer will send out a long alarm sound to remind the operator.
- Page 18 X K 3 1 9 0 –DS3 Chapter Four Maintenance and Attentions To ensure clarity of display and service life of indicator, the indicator should be used off direct sunlight and should be kept at flat place. Do not use the indicator in place of much dust, serious vibration or humidity . Connection between load cell and indicator shall be reliable and the system should have valid grounding.
- Page 19 X K 3 1 9 0 –DS3 Chapter Five Information Cue I. Regular information cue: means:Please wait, the indicator is conducting internal calculation. Do not carry out any operation now. Prnt means: Please wait; data is transmitted between the indicator and printer. LoAd means: Data save.
- Page 20 X K 3 1 9 0 –DS3 data and then restart the indicator or conduct calibration again. Err 25 means: illegally duplicated software or E PROM. destroyed Appendix 1: (applicable to printers of TYPE=2, 3 and 4) Bills in a set: Weighing Sheet Weighing Sheet Weighing Sheet...
- Page 21 X K 3 1 9 0 –DS3 Daily Sheet 2 Date: July 28, 1999 Article No. Times Total Net Weight (kg) 0001 0002 3.400 0002 0002 3.400 Appendix 3: (applicable to printers TYPE=6) Bills in a set: 0001 Date 02－03－14 Time 10 .
- Page 22 X K 3 1 9 0 –DS3 2. An example of manual and direct article weighing sheet printing Step Condition Operation Displayed Note content Load article on Press [o *****] Original vehicle no. the scale [Printing] Input “0” E.g. [ 0 ] [o 00000] “0”...
- Page 23 X K 3 1 9 0 –DS3 vehicle no. Press [Tare] [ *** ] Deduce the tare Press [o *****] Required vehicle no. [Printing] Press [Input] [hn **] Original vehicle no. Input the new article no. E.g. [ 11 ] [hn 11] If the original article number matches, please press [input] directly.