ION Audio Surf Guide D'utilisation Rapide page 5

Operation
Pairing or Disconnecting a Bluetooth Device
1. Turn on your Bluetooth device.
2. Power on Surf and it will automatically go into pairing mode to search for Bluetooth devices. You will
know you are in pairing mode when the Bluetooth icon is slowly flashing.
3. Navigate to your Bluetooth device's setup screen, find "Surf" and connect.
Note: If your Bluetooth device prompts for a pairing code, enter "0000".
4. Press and hold the Bluetooth button to disconnect a paired Bluetooth device.
5. To connect to another Bluetooth device, repeat step 3.
Note: Maximum range will be achieved when using devices with Bluetooth 4.0.
Stereo-Link™: Linking Two Speakers Together Wirelessly
1. Power on both Surfs.
Note: In order to use Stereo-Link Mode, you cannot have a Bluetooth device connected. If one
speaker is connected to a Bluetooth device, break the connection by pressing and holding the
Bluetooth button.
2. With no Bluetooth device connected (blue LEDs on both speakers will blink), on one Surf press and
hold – and + until you hear a short 3-tone melody; repeat this for the second Surf. The melody will
indicate the Surfs are searching for each other to link as their blue LEDs begin to blink fast.
3. Wait about 10-30 seconds for the Surfs to find each other. Once "linked", one Surf will say "Paired" (if
the voice prompts are enabled). Now that the two speakers are "linked," one speaker's blue LED will
be solid, while the other speaker's blue LED will blink slowly to indicate it's ready to pair the stereo-
linked speakers to your Bluetooth device (e.g., your phone).
4. When the Surfs are wirelessly linked to play in stereo, on your Bluetooth device turn on Bluetooth, and
connect to "SURF".
5. Once your smartphone is paired, you will hear "Paired" (if the voice prompts are enabled) and audio
can now play out of both speakers in stereo.
•
In Stereo-Link Mode: UI Controls on both speakers will be active.
•
To exit Stereo-Link Mode, press and hold – and + until the speaker goes back into pairing mode
saying "Ready to Pair".
•
In Stereo-Link Mode, press Power to turn off both speakers.
Note: If a Surf is in Stereo-Link Mode when you power it off, it will be in Stereo-Link the next time you
power it on. That means if two Surfs are linked when you power them off, they will automatically link when
you power them on as long as they are in close range of each other and powered on within 15 seconds of
each other.
Note: If a Surf is in Stereo-Link Mode when you power it off, when you power it back on, it will revert back
to single mode, and be ready to pair to a Bluetooth device if it does not find another Surf to link to within 15
seconds. To re-enter Stereo-Link Mode, follow Steps 1 – 5 above.
Using the Phone
Note: You must power on and pair Surf with your Bluetooth device before using it to listen to music or as a
speakerphone.
Using the Phone:
When you have an incoming call, Surf's speaker will play a ringtone.
1. To answer the call, press Surf's Call Receive/End button.
Note: If you get an incoming call during music playback, the music will pause until you end the call.
Speak into the microphone and adjust the call volume using the – and + buttons.
2.
3. To end the call, press the Call Receive/End button.
4. To reject an incoming call, press and hold the Call Receive/End button.
Troubleshooting
If the sound is distorted: Try lowering the volume control of your sound source. Also, try to reduce the
overall volume of Surf.
If there is too much bass: Try adjusting the tone or EQ control on your sound source to lower the bass
level. This will allow you to play the music louder before clipping (distortion) occurs.
5