Publicité
Starting the engine
• To start a cold engine, move the choke lever to
Engine choke (ill1-11)
• To restart a warm engine, leave the choke lever
the close position. (only cold engine)
in the open position.
• When the engine is cold the primer supplies the
Primer (ill1-12)
carburetor with more gasoline. Push the primer
at least 3 times for best performance
• Move the throttle lever about 1/3 away from the
Throttle (ill1-13)
slow (turtle) position towards the fast (rabbit)
position.
• Insert the ignition key in the keyhole.
Ignition key (ill1-14)
• Plug the cord into electrical outlet and press the
230V electric starter (ill1-15)
start button. After the engine is started remove
the plug from the socket alternatively pull the
recoil starter to crank the engine
• Pull the recoil starter gently until you feel
Recoil (Alternatively)
resistance in the rope. Then pull quickly and
energetic. Do not at any time let go of the
recoil starter but slide it gently back and pull
again.
• Push the choker gradually from close position to
Engine choke (ill1-11)
open position as the engine warms up.
Turn off the engine
To turn off the engine use the following procedure.
• Move the throttle lever from the fast (rabbit)
Throttle (ill1-13)
position towards the slow (turtle) position
• Pull the engine key.
Ignition key (ill1-14)
FUNCTION
• Push the heater button on the control panel to
Handle with embedded heat (ill1-16)
•
turn the heater for the handles on.
• Push the contact to turn the headlight on.
Front light (ill1-17)
• Pull the lever on the right side of the handlebar
Differential– Track models (ill1-19)*
in order to turn right. Pull the lever on the left
side of the handlebar in order to turn left.
*Only model 7013TGEX & 7621BEX
MACHINE OPERATION
Important! Clear and secure the work area. The
operator of the snow blower can and will be held liable
for personal injury or damage on property to injured
party.
First stage: Preparation
1. Push the throttle (ill1-13) at full throttle
(fast-rabbit)
2. Turn the chute adjusting lever (ill1-5) to adjust
the horizontal ejector angle.
3. Turn the chute adjusting lever (ill1-6) to adjust
the vertical ejector angle.
Warning: Never direct discharge at bystanders or
allow anyone in front of unit.
Caution:Depending on theamount of snow. The
ejection range can reachup to 15 meter from the chute.
Second stage: Sweeping
1. Pull the right-hand control lever to engage the
drive unit and the snow blower will start to
move. (ill1-2)
2. Use the 6 forward gears and 2 reverse (R1 and
R2) to achieve the desired working speed.
(ill1-3)
3. Push the left-hand control lever to engage the
auger unit. (ill1-4)
Note: Do not overload machine capacity by attempting
to clear snow at too fast a rate.
Advice: Select a slower speed for wet heavy snow,
and a higher speed for light powdery snow.
Warning: Not suitable forsleet!
• Exercise extreme caution when operating on
Warning!
• Do not clear snow across the face of slopes.
crossing gravel drives, walks, or roads.
• Exercise extreme caution when changing
• Do not attempt to clear steep slopes.
direction on slopes.
Auger unit
The drive shaft on auger is secured by shearing bolts.
The shearing bolts will break, if the auger strikes any
hard object, this is to prevent the snow blower from
sustain further damage. Two spare bolts with nuts are
supplied on the control panel.
Warning: Do not replace the shearing bolts with other
types of bolts!
If the chute discharger is blocked: Shut the engine
down. Ensure that all rotating parts has come to an
complete stop. Clean the Chute and auger unit using
the cleanout tool. (ill8)
13
Publicité
