Publicité
Safety instructions
• The light may only be used when mounted inside
and outside.
• To operate this product safely, the user must have
read and understood these instructions for use
before using the product for the first time.
• The product may not be used unless it is undam-
aged and functions properly. If the product or
parts of it have become defective, have it repaired
by a specialised technician.
• Always keep the operating instructions within
reach.
• If you sell or pass on the device, you must also
pass on these operating instructions.
• When working on walls, ceiling or floors, pay
attention to any installed cables as well as gas
and water lines.
• Installation may be carried out only by a suitably
qualified electrical specialist.
• Use only bulbs authorised by the manufacturer.
Do not exceed the maximum bulb power
(► Technical data – p. 13)!
• Use only connection clips authorised by the man-
ufacturer.
• Only use connection cables permitted by the
manufacturer.
• The bulb becomes hot when used! Before chang-
ing the bulb, allow to cool.
Installation
DANGER! Risk of fatal injury due to elec-
tric shock! Installation may be carried out
only by a suitably qualified electrical special-
ist.
Before installation, it must be ensured that
there is no current to the electrical network
(switch off at main switch or remove fuse).
► Assembly – p. 2
► Electrical connection – p. 4
302848, 302866, 302853, 302854
– Screw the individual pieces together securely.
– Unscrew the connection housing.
– Feed the mains cable through the cable seal.
– Connect the mains cable.
– Screw the connection housing back together
again.
– Screw the foot of the lamp securely to the floor.
– Screw the bulb into place.
– Screw the cover on tight.
302842, 302843, 302845, 302846, 302856,
302857
– Remove the connection housing from the lamp.
– Pierce cable seal.
– Feed the mains cable through the cable seal.
– Connect the mains cable.
– Screw the connection housing securely to the
wall/ceiling.
– Screws the lamp securely to the connection hous-
ing.
– Screw the bulb into place.
– Screw the cover on tight.
Exterior light
Adjusting the motion detector (only
for 302856, 302857)
► Maintenance – p. 6
1. Switch on duration
2. Switch on sensitivity
Changing the bulb
CAUTION! Danger of being burnt! The
bulb becomes hot when used! Before
changing the bulb, allow to cool.
► Changing the bulb – p. 5
Cleaning
NOTICE! Risk of damage to the device!
Do not use any sharp or abrasive objects, or
aggressive cleaning agents.
Do not use cleaning solutions.
– Wipe down the device with a dry or damp cloth.
Disposal
Disposing of the product
A crossed-out wheelie bin icon means: Bat-
teries and rechargeable batteries, electrical
or electronic devices must not be disposed of
with household waste. They may contain
substances that are harmful to the environ-
ment and human health.
Consumers must dispose of waste electrical devices,
spent portable batteries and rechargeable batteries
separately from household waste at an official collec-
tion point to ensure that these items are processed
correctly. The product can be returned free of charge
in accordance with the legal requirements, for exam-
ple through a municipal waste disposal company or a
dealer.
Batteries, rechargeable batteries and lamps
that are not permanently installed in waste
electrical equipment and can be removed in
a non-destructive way must be removed and
disposed of separately before disposal of the equip-
ment. Lithium batteries and rechargeable battery
packs of all systems are only to be handed in to the
waste collection points in a discharged state. The bat-
teries must always be protected against short circuits
by taping off the poles.
All end users are responsible for deleting any per-
sonal data stored on waste devices prior to their dis-
posal.
Technical data
Part number
Illuminant
max. lamp wattage
Rated voltage
Protection class
Connection cable
GB
302853, 302854,
302845, 302846,
302842, 302843,
302856, 302857,
302848, 302866
1× E27
60 W
230 V~, 50 Hz
I
NYM-J 3 × 1,5
13
Publicité
