Mitsubishi Electric NTXCKS.A112 Serie Manuel D'utilisation page 11

3. Operation
■
Manual vane angle (Wired remote controller)
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
Main menu: RETURN
Cursor
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Comfort
Manual vane angle
3D i-See sensor
Setting display: SELECT
Cursor
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Manual vane angle
Ref. address
Unit No.
Identify unit Check button
Input display: SELECT
Cur. Address Check
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Manual vane angle
Ref. address
Unit No.
Vane 4-way /2-way
Input display:Angle button
Cur. Cursor Angle
F1 F2 F3 F4
ON
MENU RETURN SELECT
OFF
HOLD
Manual vane angle
Select: SELECT
Outlet Angle
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Manual vane angle
Setting
Note:
Do not set the draft reduction in an environment with high humidity.
Otherwise, condensation may form and drip.
1 S e l e c t " C o m f o r t " f r o m t h e
Operation menu, and press the
[SELECT/HOLD] button.
2 Select "Manual vane angle" with
the [F1] or [F2] button, and press
the [SELECT/HOLD] button.
3 Move the cursor to "Ref. address"
or "Unit No." with the [F1] button
to select.
Select the refrigerant address
and the unit number for the units
to whose vanes are to be fi xed,
with the [F2] or [F3] button,
and press the [SELECT/HOLD]
button.
• Ref. address: Refrigerant address
• Unit No.: 1, 2, 3, 4
Press the [F4] button to confi rm
the unit.
Select "Vane" with the [F1] button.
Select "4-way" or "2-way" with the
[F2] or [F3] button, and press the
[F4] button.
4 The current vane setting will
appear.
Select the desired outlets from
"1","2", "3", "4", or "1, 2, 3, 4 (all
outlets)" with the [F1] or [F2]
button.
Press the [F3] or [F4] button to go
through the following options and
select the desired setting.
* Draft reduction
The airfl ow direction for this
setting is more horizontal than the
airfl ow direction for the "Step 1"
setting in order to reduce a drafty
feeling. The draft reduction can
be set for only 1 vane.
■
Vane setting
No setting Step 1
Step 3 Step 4
Draft
All outlets
reduction*
Press the [SELECT/HOLD] button to save the settings.
A screen will appear that indicates the setting information is being trans-
mitted.
The setting changes will be made to the selected outlet.
The screen will automatically return to the one shown above when the
transmission is completed.
Make the settings for other outlets, following the same procedures.
If all outlets are selected,
the unit goes into operation.
Navigating through the screens
• To go back to the Main menu ................ [MENU] button
• To return to the previous screen .......... [RETURN] button
■
Manual vane angle (Wireless remote controller)
Fig. 1
Fig. 2
Fig. 3
Display
Setting Step 1
Display
Setting Step 5 No setting
* The draft reduction can be set for only 1 vane.
The setting is enabled only for the last vane that was set.
Step 2
Step 5
will be displayed the next time
1 Going to the Manual vane setting
mode
Press the button.
(Start this operation from the status
of remote controller display turned
off .)
"FUNCTION" is lit and "1" blinks.
(Fig. 1)
Press the button to select "2",
and then press the
2 Selecting the vane number (Fig. 2)
Press the buttons to select the
vane number A, and then press
the button.
A
3 Setting the vane angle (Fig. 3)
Press the buttons to select the
vane angle B.
Point the wireless remote controller
B
toward the receiver on the indoor
unit, and then press the
button.
Step 2 Step 3 Step 4
No display
Draft reduction*
button.
10