Publicité
• The product must not be operated in rooms with
bathtubs, showers or swimming pools or near to
wash basins or water connections.
• Remember that moving parts may also be located
behind ventilation and venting slots.
• If the power cord of this device is damaged, it
must be replaced by the manufacturer, its cus-
tomer service department or a similarly qualified
person, in order to avoid potential hazards.
• Symbols appearing on your device may not be
removed or covered. Signs on the device that are
no longer legible must be replaced immediately.
Read and observe the instructions for use
before using the product for the first time.
Unpacking and assembly
Unpacking
Unpacking the product and checking for completeness.
Scope of delivery
• Table fan
• Remote control (2 × AAA batteries – not included)
• Instructions for use
Your product at a glance
Note: The actual appearance of your
product may differ from the illustrations.
► Overview – p. 2
1. Air outlet
2. Control panel
3. Body
Operation
Check before switching on!
DANGER! Caution, risk of injury! The
product may only be put into operation if
no faults are found during the check-up.
Ensure that any defective parts are
replaced before the product is used again.
Check the safe condition of the product:
– Check whether there are any visible defects.
– Check whether all parts of the product are firmly
attached.
Switching On/Off
► P. 3, fig. 1
1. Reservation/Timer
2. Low speed
3. Midgear speed
4. High speed
5. Standby
6. Natural mode
7. Sleep mode
– Plug in the power, the standby indicator will on.
• ON/OFF button
– To turn ON press the "ON/OFF" button. The
midgear indicator light will turn on, and the fan
will start operation. To turn OFF, press the "ON/
OFF" button. The midgear indicator light will
turn off, and the fan will stop operation. The
standby indicator light will always remain on.
• Speed button
– The fan defaults to a midgear speed when it is
turned on. You can change the fan speed by
touching the "Speed" button.
• Mode button
– When the speed mode, press the "Mode" but-
ton to set the natural mode and sleep mode.
• Swing button
– When the fan is on, press the "Swing" button.
The fan will then automatically start to move
direction. To make the fan into a fixed position
again, press the "Swing" button.
• Timer-On/Timer button
• Time function
– Press the "Time" button repeatedly to set a
period after which the fan will turn itself off
(From 1 hour – 15 hours).
• Time-On function
– You can set the Time-On function when the fan is in
standby mode. Press the "Time" button to set the
time. Then press the "Speed" button and "Mode"
button to set the wind speed and mode. If you press
the "ON/OFF" button, this function will be closed.
Remote control
Note: This fan comes with a remote con-
trol. You can also control the fan by using
the push buttons on the remote control.
– Please follow below way to assemble batteries.
► P. 3, fig. 2
– Open the battery case as shown.
– Put the battery into the battery box, pay attention
to the positive and negative electrodes of the bat-
tery. Please use 2 × AAA batteries.
– Cover the battery case.
► P. 3, fig. 3
8. ON/OFF button
9. Swing button
10. Speed button
11. Time-On/Time button
12. Mode button
Cleaning
DANGER! Caution, risk of injury!
Always pull the mains plug out before
commencing any work on the product.
– Turn off the product, pull out the mains plug.
– Wipe the product with a slightly damp cloth.
Storage and transport
Storing
– Store the device and any accessories in a dry,
well-ventilated place.
– In case of longer periods without operation, protect the
device and its accessories against soiling and corrosion.
– If the device is not used for an extended period
(overwintering), store it in a dry frost-free location.
GB
17
Publicité
