Publicité
ATTENTION! Before installation, make sure that the dryer is not
connected to the electrical system
1.
The appliance may only be connected to an power socket equipped with
a PE protective circuit connection.
2.
When supplying power directly from the electrical installation, ensure
that the power supply is disconnected
3.
Screw the dryer mounts included in the kit to the wall (Fig. 3.8, 3.9)
4.
Connect the wires of the power supply cord or the electrical installation
to the terminal blocks (Fig. 3.10)
5.
Follow the guidelines when connecting the appliance permanently to
the installation (Fig. 4):
a)
Brown wire insulation - phase circuit (L),
b)
Blue wire insulation - neutral circuit (N),
c)
Yellow-green wire insulation - protective (earthing) circuit (PE).
6.
Put the hangers (Fig. 3.2) and the head (Fig. 3.12) on the dryer
mounts screwed to the wall (Figs. 3.8, 3.9) and lock them in place
using the grub screws (Fig. 3.7) included in the kit.
7.
Before starting the electric heating element for the first time, its
condition must be verified, see point VII.
VII. Verification of device condition (Figure 3)
Pay particular attention to the information contained in
this section. Not following the safety rules may
endanger life, health or property.
The appliance should be visually inspected before first start-up, and
periodically during usage. Condition inspection is recommended
according to the list below:
1. Condition of the dryer mounting to the wall
Ensure that there is no loose fitting at the mounting brackets (Fig. 3.8)
and the head (Fig. 3.12). The dryer must be securely fixed to the wall
to ensure safe use.
2. Condition of the electrical supply connection (in dryers equipped with
a supply cord)
To be verified:
· condition of the power supply cord insulation (no visible damage to
the insulation - deep scratches, cracks)
· condition of the plug (no cracks, no loose connection pins, a tightly
fixed cable)
· connection of the cord to the device (the cord must be tightly and
securely fixed)
3. Proper heating up of the dryer
Approximately 30 minutes after start-up, the dryer should be noticeably
warmed up.
VIII. Functionality
1. The dryer is designed for continuous operation
2. The temperature on the surface of the dryer does not exceed 60°C
3. The maximum temperature of the dryer surface covered by hanging a
towel or bathrobe is 55°C.
4. The maximum surface temperature of an uncovered dryer - without a
towel or bathrobe - is 50°C.
5. The minimum surface temperature of an uncovered dryer - without a
towel or bathrobe - is 40°C.
IX. Operation (Figure 3)
1. At the top of the appliance, there is a pushbutton switch (Fig. 3.4) that
allows to switch the dryer on and off.
2. The operation (heating) of the dryer is indicated by the illumination of the
blue LED in the upper part of the device (Fig. 3.3)
3. The dryer is equipped with hangers (Fig. 3.2) for hanging towels and
clothes.
X. Demounting the dryer (Figure 3)
Demounting of the appliance may only be carried out
by an installer with the appropriate qualifications.
- 10 -
English
1. Switch the dryer off using the pushbutton and:
a) for an appliance equipped with a power cord - remove the plug from the
power supply socket.
b) If the appliance is equipped with a masking cable, disconnect the power
supply to the appliance using the switch described in point II.A.7.
2. Loosen the grub screws on the mounting brackets and masking cover
(Fig. 3.7) and pull the head (Fig. 3.12) away from the wall, then
disconnect the wires from the connection terminals (Fig. 3.10).
3. Remove the dryer from the brackets fixed to the wall (Fig. 3.8, 3.9)
XI. Maintenance
Make sure the appliance is cooled down before carrying out maintenance.
We recommend using a soft cloth or sponge for cleaning. Under no
circumstances should corrosive or abrasive cleaning agents or sharp
objects be used - this will prevent damage to the decorative finish.
·
Clean painted surfaces with warm water and soft cleaning agents.
·
Chrome surfaces should be cleaned with a cleaning agent designed for
this purpose.
XII. Transport and storage conditions
During transport and storage, the device should not be exposed to:
1. Direct contact with water
2. Tempeatures outside the range of 5°C to 35°C
3. Air humidity exceeding 70%
4. Exposure to significant forces and overloads that can damage electronics
Exposure of the device to the above-mentioned factors may result in
damage to the electronics
XIII. Disposal
After use, the product must not be disposed of as municipal waste. The
device is subject to special requirements concerning the management of
electrical and electronic waste. Take the appliance to a collection and
recycling centre for electrical and electronic equipment. Information on
the correct disposal point for used appliances will be provided by your
sales agent or the manufacturer.
By acting in accordance with the principles of proper disposal,
you are making your own contribution to the protection of the
environment
XIV. Warranty conditions (Figure 6)
1. The product manufactured by VASCO GROUP nv. described in this manual is
the subject of the guarantee.
2. The warranty period is 24 months from the date of purchase, but no longer
than 36 months from the date of production. Identification of the date of
production is possible with the serial number on the back of the housing. Year
of manufacture: first two digits of the serial number - 23 = 2023 (Fig. 6)
3. The basis for warranty claims is the proof of purchase of the product. The
absence of this proof entitles the manufacturer to reject the claim.
4. By receiving the appliance at the time of purchase, the customer confirms its
completeness. If the customer does not raise any objections to the product - in
particular to the quality of the decorative surfaces - it is assumed that the
product has been delivered without defects.
5. The warranty does not cover damage caused by incorrect
assembly/disassembly and incorrect use of the appliance. Please, read this
manual, which forms an integral part of the warranty, before using.
6. The manufacturer have 14 working days from the date of delivery of the faulty
product to the manufacturer's factory for the expertise and repair of the faulty
product.
7. If repair is not possible, the manufacturer undertakes to supply a new product
with the same parameters.
Manufacturer:
VASCO GROUP nv
Kruishoefstraat 50
B-3650 Dilsen-Stokkem
info@vasco.be
www.vasco.eu
Publicité
