Publicité
Operate the leaf vacuum using only the nozzle
and the connected collection bag. Replace worn
or damaged components.
Do not use this leaf blower near fire places or
BBQ places and open fire, ash pits, etc. A proper
use of the leaf blower contributes to fire spread
avoidance.
Do not work near open
Do not put any objects on the lance blow ope-
nings. Make sure the blown material is not being
blown at persons, animals, glass sheets or solid
objects such as trees, cars, walls, etc. Strong air
flow could throw off stones, dirt or rods or they could
be bounced off the ground and injure persons,
animals, break glass sheets or cause other damage.
Never use the appliance to disperse chemicals,
fertilisers or other substances. By this, you will
avoid toxic material spread.
Operation
The on/off speed control knob (2) is located on the
front of the rear handle, which is used to turn the
tool on and off and is also a variable controller for
motor speed.
To turn the fan on, scroll the running speed control
button (2)
Stop turning the cruise control knob until the engine
is running at the required speed.
Press the "Turbo" acceleration button (1) and the
machine reaches maximum power (Figure 17/18)
To switch the tool off: turn the on/off speed control
knob (2) to the "off" position. (Figure 17/18)
Gripping and guiding the tool during operation
When the tool is in operation, always stand behind
the tool and hold it firmly with both hands by the
handles.
Speed adjustment
This tool is equipped with a speed regulator (7) with
which you can control the speed of the blown air
and the sucked air. To adjust the speed, turn the
regulator "2" towards "MAX" to increase or decrease
the speed.
Clearing an Obstruction
Your 40V cordless leaf blower is equipped with a
clean-out hatch (4).
When the impeller is clogged, it is accessible for
cleaning.
Open the cleanout door by loosening the
thumbscrew to remove debris.
WARNING
windows etc.
Using the blow function
Any hard object such as
rocks, cans, etc. will be
projected by blowing.
Inspect the work area before starting. Remove any
objects or debris that could be blown by the
cordless leaf blower.
Select the blow function using the selection lever
(13) located on the side of the tool and switch the
tool on. With the cordless leaf blower resting on its
wheels, move it forward aiming the nozzle at the
debris to be blown.
You can also hold the nozzle just above the ground
and rock the tool from side to side, moving forward
and aiming the nozzle at the debris to be blown.
Blow away the debris in a pile, then use the vacuum
function to pick up the debris.
Using the suction function
Inspect the work area before starting. Remove any
objects or debris that could become caught or
tangled in the cordless leaf blower. Select the
suction function using the selection lever (13) on the
side of the tool and switch the tool on.
With the cordless leaf blower resting on its wheels,
move it forward aiming the nozzle at the debris to be
vacuumed.
You can also hold the blower just above the ground
and rock the tool from side to side, moving forward
and aiming the nozzle at the debris to be vacuumed.
Do not force the nozzle into
the debris, this will block the
vacuum tube and reduce the
effectiveness of the tool.
Organic materials such as
leaves contain a large amount
of water which can cause
them to stick inside the
To reduce adhesion, these
materials should be allowed
to dry for a few days.
▪ When the blower is used in suction mode, debris is
sucked into the suction tube before being ejected
into the collection bag (11).
▪ The suction turbine is equipped with a knife, which
significantly increases the crushing capacity.
▪ Debris is crushed as it passes through the suction
turbine.
▪ Crushed organic debris is ideal as a mulch around
plants.
If the component begins to
vibrate unusually, stop the
engine and investigate the
vacuum tube.
WARNING
31
Publicité
