e-conolight Savr E-FLA Serie Guide D'instructions D'installation

INSTALLATION INSTRUCTIONS
E-FFD-B Series
CAUTIONS
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions
should always be followed including the following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. DANGER- Risk of shock- Disconnect power before
installation.
DANGER – Risque de choc – Couper l'alimentation
avant l'installation.
2. This luminaire must be installed in accordance with the
NEC or your local electrical code. If you are not familiar
with these codes and requirements, consult a qualified
electrician.
Ce produit doit être installé conformément à NEC ou
votre code électrique local. Si vous n'êtes pas familier
avec ces codes et ces exigences, veuillez contacter un
électricien qualifié.
3. Suitable for Wet Locations.
Adspte pour les Endroits Mouiles.
SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE
NOTES:
1. When mounting the fixture in an inverted position (1/2" fitter
above fixture), mount fixture to a watertight junction box and
cover. Also, caulk the conduit openings, around the junction box
cover, and the wire entry end of the 1/2" fitter with a high grade
caulking material, such as silicone rubber, to ensure water does
not enter fixture through 1/2" fitter.
www.e-conolight.com |
Document: LPN00704X0001A1_A
Created By: TMT
MOUNTING USING YOKE
1. Mount 4L, 6L and 9L using (2) customer supplied fasteners and
washers appropriate for the mounting surface.
2. Aim fixture by loosening the bolts on both sides of the yoke and
rotating the fixture to the desired tilt angle. Re-tighten bolts.
3. Route the fixture's 18AWG cord to the junction box where the
supply leads can be accessed. The fixture cord has a 0.3125"
(8mm) outside diameter. A UL listed watertight cord grip suitable
for use on 0.3125" (8mm) diameter wet location flexible cord shall
be supplied (by others) to install cord onto outdoor junction box.
NOTE: To reduce the risk of water entering the junction box, a
sealing compound should be used on the thread portion of the
cord grip. It is recommended that the watertight cord grip be
installed so that the fixture cord exists the junction box toward
the ground. if the junction box does not allow for the cord to exit
toward the ground, the use of an elbow suitable for wet location
use is recommended so that the cord can exit toward the ground.
4. Make wiring connections per Fixture Wiring section.
MOUNTING USING 1/2" FITTER
1. Thread the floodlight mounting arm into the 1/2" opening of the
cover and secure it with 1/2" locknut. Using a sealing compound
on the threads will ensure a water tight seal.
2. Wire as indicated in the fixture wiring section.
3. Aim the fixture by loosening the screw on knuckle of fitter and
rotate fixture to the desired angle. Re-tighten the screw.
Fixture is equipped with a 120V driver. Make sure supply voltage
is 120V AC.
1. Connect supply ground to fixture ground (green or bare) lead.
2. Connect supply common to fixture neutral (white) lead.
3. Connect supply Vin (120V AC) to fixture hot (black) lead.
Tuck all wires carefully into wiring chamber ensuring that no wires
are pinched.
FCC NOTICE Class A
CAUTION: Changes or modifications not expressly approved could
void your authority to use this equipment.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CAN ICES-005 (A)/NMB-005 (A)
888.243.9445 | FAX: 262.504.5409
Date
FIXTURE WIRING
5/20/2024