How To Use; Thinning Materials - Homeright Super Finish Max Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

The Super Finish Max allows you the ultimate control for your spray pattern. With this unit you can change the spray tip set to adjust the flow of
material. You can also select a fine or wide air cap nozzle that also controls the flow of material for the sprayer. Dial in the actual spray pattern by
adjusting the flow control knob on the unit either + or – to your desired width. This allows you to use this sprayer for small detailed craft projects,
furniture or large fences and decks.
The sprayer comes with a 1.5 mm, 2.0 mm and 4.0 mm spray tip set. The spray tip sets are changeable with the wrench tool, simply turn the tip
counterclockwise to loosen the tip. Then use the other end of the tool to loosen the tip. Place the desired pin on the needle and then tighten or snug
with included wrench tool. Then place the matching (tips and pins are color coded) spray tip on and tighten with the tool. The sprayer comes with the
2.0 mm spray tip set installed and fine air cap.
Yellow Air Cap Nozzle = Wide spray pattern and is used for high production projects like large decks and fences.
Black Air Cap Nozzle = Fine spray pattern and is used for furniture, cabinets and anything requiring a fine finish.
Spray Tip
Spray Tip
Set Size
Set Color
1.0 mm
Orange
1.5 mm*
Blue
2.0 mm*
Green
2.5 mm
Yellow
3.5 mm
Black
4.0 mm*
Red
*Included with Super Finish Max unit.
**Water and oil based materials can be used in the Super Finish Max.

THINNING MATERIALS

In order for your sprayer to operate properly it is important to make sure the stain or
paint is thin enough to be sprayed. Thinning should be followed per the stain or paint
manufacturer's guidelines. Because materials differ from brand to brand, this guide can
offer only general information. Always follow the coverage rate recommended by the
manufacturer regardless of the thinning required. Because there is a variance in viscosity
between paint and stain brands, it might be necessary to thin 5 to 15 percent to achieve
optimum spray pattern.
NOTES:
∙ Be sure pick-up tube is inserted tightly into the intake port.
∙ Thin material according to the procedure outlined above.
∙ Before each use, check the Brass Fluid Nozzle and Brass Fluid Needle for dried paint.
Keep Brass Fluid Needle clean.
∙ Always thoroughly clean the sprayer after each use.
(See CLEAN UP AND MAINTENANCE, page 8.)
∙ Turn control knob counterclockwise for less flow — see Page 6 Step 7 for more detail.
∙ Strain old paint or stain before using.
∙ Slowly stir paint or stain. To prevent air bubbles, do not shake stain or paint.

HOW TO USE

Recommended Material**
Sealers and varnish
Stains and polyurethane
Latex paint, chalk type paint,
milk type paint
Latex paint, chalk type paint,
milk type paint
Primer and latex paint
Primer and latex paint
SUPER FINISH MAX
SPRAYER
®
(C800971)
Spray
Outcome
1-4" Spray pattern/
fine finish
1-6" Spray pattern/
fine finish
1-6" Spray pattern/
fine finish
6-7" Spray pattern/
fine finish to medium finish
8-10" Spray pattern/
medium finish
10-12" Spray pattern/
medium finish
5
Project
Type
Furniture and
woodworking projects
Furniture and
woodworking projects
Furniture and
cabinets
Furniture and
cabinets
Walls, ceilings, decks
and fences
Walls, ceilings, decks
and fences
A
Use the included wrench to loosen the tip and
nozzle. Replace with desired tip and nozzle
and snug with wrench.
Air Cap
Nozzle
Black
Black
Black
Black
Yellow
Yellow
ENGLISH

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Finish max450-0100

Table des Matières