Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
DT150-C Product HANDBOOK
General Safety Instructions:
READ SAFETY INSTRUCTIONS
Servicing:
These products are not customer serviceable. TDK-Lambda UK LTD. and their authorised agents only are
permitted to carry out repairs.
Critical Components:
These products are not authorised for use as critical components in nuclear control systems, life support
systems or equipment for use in hazardous environments without the express written approval of the
Managing Director of TDK-Lambda EMEA.
Product Usage:
These products are designed for use within a host equipment which restricts access to authorised competent
personnel.
This product is a component power supply considered apparatus and is only to be installed by qualified
persons as part of a final equipment and must not be operated as a stand-alone product.
This product is for sale to business to business customers and can be obtained via distribution channels. It is
not intended for sale to end users.
This product is considered to be an apparatus and complies with the EMC Directive. Compliance with the
EMC Directive must be considered in the final installation. Please contact your local TDK-Lambda office.
Environmental:
These products are IP20 construction, and therefore chemicals/solvents, cleaning agents and other liquids
must not be used.
Environment:
This power supply is a switch mode power supply for use in applications within a Pollution Degree 2,
overvoltage category II environment. Material Group IIIb PCB's are used within it.
Output Loading:
The output power taken from the power supply must not exceed the rating stated on the power supply label,
except as stated in the product limitations in this handbook.
Input Parameters:
This product must be operated within the input parameters stated in the product limitations in this handbook.
End of Life Disposal:
The unit contains components that require special disposal. Make sure that the unit is properly disposed of at
the end of its service life and in accordance with local regulations.
RISK OF ELECTRIC SHOCK
High Voltage Warning:
Dangerous voltages are present within the power supply. Under no circumstances can the power supply be
opened.
This product must be reliably earthed and professionally installed in accordance with the prevailing local
electrical wiring regulations and safety standards.
An internal fuse protects the unit and must not be replaced by the user. In case of internal defect, the unit
must be returned to TDK-Lambda UK LTD or one of their authorised agents.
Page 1 of 16
260371 issue 1, May 2017
Publicité
Table des Matières
Manuels Connexes pour TDK-Lambda DT150-C
Sommaire des Matières pour TDK-Lambda DT150-C
- Page 1 General Safety Instructions: READ SAFETY INSTRUCTIONS Servicing: These products are not customer serviceable. TDK-Lambda UK LTD. and their authorised agents only are permitted to carry out repairs. Critical Components: These products are not authorised for use as critical components in nuclear control systems, life support systems or equipment for use in hazardous environments without the express written approval of the Managing Director of TDK-Lambda EMEA.
-
Page 2: Hot Surface
DT150-C Product HANDBOOK HOT SURFACE External Hot Surfaces: In accordance with local regulations for Health and Safety at work, manufacturers have an obligation to protect service engineers as well as users. In order to comply with this, a label must be fitted to these... - Page 3 Allgemeine Sicherheitsvorschriften: LESEN SIE DIE SICHERHEITSVORSCHRIFTEN Wartung: Diese Produkte können nicht durch den Kunden gewartet werden. Nur TDK-Lambda UK LTD. und deren zugelassene Vertriebshändler sind zur Durchführung von Reparaturen berechtigt. Kritische Komponenten: Diese Produkte sind nicht für die Verwendung als kritische Komponenten in nuklearen Kontrollsystemen, Lebenserhaltungssystemen oder Geräten in gefährlichen Umgebungen geeignet, sofern dies nicht...
-
Page 4: Gefahr Durch Elektrischen Schlag
Bestimmungen zu Verdrahtungen sowie den Sicherheitsstandards installiert werden. Eine interne Sicherung schützt das Gerät und darf durch den Benutzer nicht ausgetauscht werden. Im Fall von internen Defekten muss das Gerät an TDK-Lambda UK LTD oder einen der autorisierten Vertriebshändler zurückgeschickt werden. -
Page 5: Lire Les Consignes De Securite
Consignes de sécurité générale: LIRE LES CONSIGNES DE SECURITE Entretien: Ces produits ne peuvent pas être réparés par le client. Seul, TDK-Lambda UK LTD et ses agents agréés sont autorisés à effectuer des réparations. Composants critiques: Ces produits ne doivent pas être utilisés en tant que composants critiques dans des systèmes de commande nucléaire, dans des systèmes de sauvetage ou dans des équipements utilisés dans des environnements... -
Page 6: Risque De Choc Electrique
électriques en vigueur et les normes de sécurité. Un fusible interne protège le module et ne doit pas être remplacé par l'utilisateur. En cas de défaut interne, le module doit être renvoyé à TDK-Lambda UK LTD ou l'un de ses agents agréés. SURFACE CHAUDE Surfaces chaudes extérieures:... - Page 7 Questo alimentatore è da considerarsi come un componente e come tale non è assogettato dagli scopi della direttiva EMC. Conformità alla direttiva EMC deve essere considerata nell'installazione finale di utilizzo. Gli uffici di TDK-Lambda Sas Succursale Italiana sono a vostra disposizione per ulteriori ragguagli Condizioni ambientali: Questi prodotti sono classificati come IPX0, dunque non devono essere utilizzati sostanze chimiche/solventi, prodotti per la pulizia o liquidi di altra natura.
- Page 8 Un fusibile interno protegge l'unità e non deve essere sostituito dall'utente. Nell'eventualità di un difetto interno, restituire l'unità a TDK-Lambda UK LTD o a uno dei suoi agenti autorizzati SUPERFICIE CALDA Superfici esterne calde: Coerentemente con le norme locali in materia di salute &...
- Page 9 Instrucciones generales de seguridad: LEA LAS INSTRUCCIONES DE SEGURIDAD Servicio: Estos productos no pueden ser reparados por los clientes. TDK-Lambda UK LTD. y sus agentes autorizados son los únicos que pueden llevar a cabo las reparaciones. Componentes fundamentales: Estos productos no pueden ser utilizados como componentes fundamentales en sistemas de control nuclear, sistemas de soporte vital o equipos a utilizar en entornos peligrosos sin el consentimiento expreso por escrito del Director General de TDK-Lambda EMEA.
- Page 10 Un fusible interno protege la unidad y este no debe ser nunca reemplazado por el usuario. En caso de existir algún defecto interno, la unidad debe ser enviada a TDK-Lambda UK LTD o a uno de sus agentes autorizados.
- Page 11 Instruções gerais de segurança: LEIA AS INSTRUÇÕES DE SEGURANÇA Manutenção: Estes produtos não são podem ser submetidos a manutenção por parte do cliente. Apenas a TDK-Lambda UK LTD e os seus agentes autorizados têm permissão para realizar reparações. Componentes essenciais: Não é...
-
Page 12: Risco De Choque Eléctrico
Existe um fusível interno que protege a unidade e que não deve ser substituído pelo utilizador. Em caso de defeito interno, a unidade deve ser devolvida à TDK-Lambda UK LTD ou a um dos seus agentes autorizados. SUPERFÍCIE QUENTE Superfícies quentes externas:... - Page 13 TDK Lambda UK Ltd is a member of the B2B Compliance scheme; the scheme is operated by GAMBICA B2B Compliance Ltd For further information relating to the obligations of TDK-Lambda under the WEEE Directive please contact B2B Compliance on +44 (0)1691 676124, you can also contact them via e-mail at WWW.b2bcompliance.org.uk...
- Page 14 DT150-C Product HANDBOOK Input Connections: Class I AC inlet (3 pin) IEC320-C14 (accepts IEC320-C13) Output Parameters: Output channel Vout (V) Output Maximum current (A) power (W) DT150PW120-C 11.67 DT150PW160-C 9.38 DT150PW190-C 7.90 DT150PW240-C 6.25 DT150PW360-C 4.17 DT150PW480-C 3.13 The DC output cable: Type 1: 1050mm, 14AWG/1C + shielding, VW-1, UL 80°C, 30V (12-24V models)
- Page 15 DT150-C Product HANDBOOK Cooling for unit The DT150-C products are external power supplies. To ensure correct thermal performance at full load the product should be installed in the end use equipment as below and the operating ambient must not exceed 40°C.
- Page 16 DT150-C Product HANDBOOK Mechanical Drawings: Fusing: The product is dual fused in the L and N line, T3.15A, 250V. The product is not user serviceable. Fuses must not be replaced by the user. TDK-Lambda UK Ltd Kingsley Avenue, Ilfracombe Devon, EX34 8ES Telephone - Sales and Service +44 (0)1271 856666 Head Office and Works +44 (0)1271 856600...