screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
NOTE: Do not attempt to mount CMCB101 charger under a
bench or table.
NOTE: Only mount CMCB101 charger with the charging
lights pointed upward toward the ceiling.
VersaTrack™
WARNING: Do not charge batteries while charger is
hung on Trackwall.
CRAFTSMAN chargers, except the CMCB101, can
be stored on CRAFTSMAN VersaTrack™ Trackwall.
Hooks and accessories are sold separately. Please
refer to the VersaTrack™ Trackwall accessory sheet for
further information.
NOTE: The CMCB101 charger is not CRAFTSMAN
VersaTrack™ Trackwall compatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Anvil (Fig. D)
CAUTION: Inspect anvil prior to use. Missing or
damaged items should be replaced before use.
To install an accessory on the anvil, align the accessory
2
with the anvil
. Press the accessory onto the anvil.
To remove an accessory, pull the accessory off the anvil.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. E)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
NOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery pack release button
pack out of the tool handle. Insert it into the charger as
described in the charger section of this manual.
5
into the tool handle, align
4
and firmly pull the battery
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
WARNING: Ratchet may stall (if overloaded or
improperly used) causing a twist. Always expect the
stall. Grip the ratchet firmly to control the twisting
action and prevent loss of control which could cause
personal injury.
Proper hand position requires one hand on the main handle
as shown to control the twisting action of the ratchet.
Variable Speed Trigger (Fig. A)
The tool is turned on and off by pulling and releasing the
1
variable speed trigger
. The farther the trigger is depressed,
the higher the speed of the tool. The anvil will stop as soon
as the trigger switch is fully released.
Forward/Reverse Dial (Fig. A, G)
3
A forward/reverse dial
of the tool.
•
To select forward rotation (clockwise), release the trigger
and rotate the forward/reverse dial on the head of
the tool in a counterclockwise direction.
•
To select reverse rotation (counterclockwise), release the
trigger and rotate the forward/reverse dial on the head of
the tool in a clockwise direction.
NOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start up. This is
normal and does not indicate a problem.
Lock‑off Button (Fig. A)
To lock the tool, slide the lock‑off button
position. When the lock‑off button is in the locked position,
the tool is locked and the trigger switch
Worklight (Fig. A)
6
The worklight
is activated when the trigger switch
depressed, and will automatically turn off 10 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
NOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Usage (Fig. A, E)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
WARNING: The ratchet may stall if overloaded causing
a sudden twist. Always expect the tool to twist. Grip the
ratchet firmly to control the twisting action and avoid
possible personal injury.
CAUTION: Ensure fastener and/or system will
withstand the level of torque generated by the tool.
determines the rotational direction
8
to the locked
1
cannot be pulled.
ENgliSh
7
1
is
9