Bosch 1400 Série Guide D'installation page 45

1400 Series IP Video Storage Array
MegaCli -v
MegaCli -help|-h|?
MegaCli -adpCount
MegaCli -AdpSetProp {CacheFlushInterval -val} | { RebuildRate -val}
MegaCli -AdpSetProp -AutoDetectBackPlaneDsbl -val -aN|-a0,1,2|-aALL
MegaCli -AdpSetProp -CopyBackDsbl -val -aN|-a0,1,2|-aALL
MegaCli -AdpSetProp -EnableJBOD -val -aN|-a0,1,2|-aALL
MegaCli -AdpSetProp -DsblCacheBypass -val -aN|-a0,1,2|-aALL
MegaCli -AdpSetProp -LoadBalanceMode -val -aN|-a0,1,2|-aALL
MegaCli -AdpSetProp -UseFDEOnlyEncrypt -val -aN|-a0,1,2|-aALL
MegaCli -AdpSetProp -PrCorrectUncfgdAreas -val -aN|-a0,1,2|-aALL
MegaCli -AdpSetProp -DsblSpinDownHSP -val -aN|-a0,1,2|-aALL
MegaCli -AdpGetProp CacheFlushInterval | RebuildRate | PatrolReadRate
Bosch Sicherheitssysteme GmbH
| {PatrolReadRate -val} | {BgiRate -val} | {CCRate -val}
| {ReconRate -val} | {SpinupDriveCount -val} | {SpinupDelay -val}
| {CoercionMode -val} | {ClusterEnable -val} | {PredFailPollInterval -val}
| {BatWarnDsbl -val} | {EccBucketSize -val} | {EccBucketLeakRate -val}
| {AbortCCOnError -val} | AlarmEnbl | AlarmDsbl | AlarmSilence
| {SMARTCpyBkEnbl -val} | {SSDSMARTCpyBkEnbl -val} | NCQEnbl | NCQDsbl
| {MaintainPdFailHistoryEnbl -val} | {RstrHotSpareOnInsert -val}
| {EnblSpinDownUnConfigDrvs -val} | {EnblSSDPatrolRead -val}
| {DisableOCR -val} | {BootWithPinnedCache -val}
| AutoEnhancedImportEnbl | AutoEnhancedImportDsbl -aN|-a0,1,2|-aALL
| {ExposeEnclDevicesEnbl -val} -aN|-a0,1,2|-aALL
| {DsblSpinDownHsp -val} -aN|-a0,1,2|-aALL
| {SpinDownTime -val} -aN|-a0,1,2|-aALL
val - 0 = Activer auto détection de SGPIO et i2c SEP.
1 = Désactiver auto détection de SGPIO.
2 = Désactiver auto détection de i2c SEP.
3 = Désactiver auto détection de SGPIO et i2c SEP.
val - 0 = Activer Copyback.
1 = Désactiver Copyback.
val - 0 = Désactiver mode JBOD.
1 = Activer mode JBOD.
val - 0 = Activer exclusion cache.
1 = Déactiver exclusion cache.
val - 0 = Mode Load balance auto.
1 = Désactiver mode Load balance.
val - 0 = Chiffrement FDE et contrôleur (si pris en charge par le matériel) autorisé.
1 = Chiffrement FDE uniquement, chiffrement contrôleur non autorisé.
val - 0 = Correction de l'erreur de support lors de PR désactivée.
1 = Correction de l'erreur de support lors de PR autorisée.
val - 0 = Ralentissement du disque de secours autorisé.
1 = Ralentissement du disque de secours désactivé.
| BgiRate | CCRate | ReconRate | SpinupDriveCount | SpinupDelay
| CoercionMode | ClusterEnable | PredFailPollInterval | BatWarnDsbl
| EccBucketSize | EccBucketLeakRate | EccBucketCount | AbortCCOnError
| AlarmDsply | SMARTCpyBkEnbl | SSDSMARTCpyBkEnbl | NCQDsply
| MaintainPdFailHistoryEnbl | RstrHotSpareOnInsert
Guide d'installation
Annexe | fr 45
DOC | V1 | 2010.08