Publicité
42
SPECIFICAtIONS
Before calling for service (cont.)
Problem
Steam does not
• Water level error.
generate but no error
code is shown
Garments still
• Too many or too different types of garments
wrinkled after
in dryer.
STEAM FRESH™
There are no creases
• The function of this cycle is to remove
left on garment after
wrinkles from fabric.
STEAM FRESH™
Garments have
• This is normal.
static after REDUCE
STATIC
Garments are too
• Correct drying options not selected.
damp or too dry after
REDUCE STATIC
Garments are not uniformly
• Number of garments or load size not properly
damp after EASY IRON
selected at the beginning of the cycle.
Water drips from door
• This is normal.
during Steam Cycle
Steam is not visible
• This is normal.
during Steam Cycle
Drum does not turn
• This is normal.
during Steam Cycle
Cannot see steam
• This is normal.
vapor at the
beginning of cycle
The display shows
• MORE TIME button pressed.
Odors remain in
• STEAM FRESH™ did not remove odor
clothing after
completely.
STEAM FRESH™
CHECK FILTER light
• Lint filter is almost clogged or full.
is on during the
drying cycle
TM
FLOW SENSE
• Ductwork is too long or has too many turns/
indicator shows four
restrictions.
bars during the drying
• Significant blockage of the ductwork due to
cycle
lint buildup or debris.
• The appliance has detected a restriction in
the external dryer venting.
SPECIFICATIONS
Steam Dryer™ Models
Description
Electrical Requirements*
Gas Requirements*
Dimensions
Net Weight
Drying Capacity
- Normal Cycle
- Steam Cycle
All manuals and user guides at all-guides.com
Possible Causes
DLEx3550* DLGx3551*
Steam Dryer
Please refer to the rating label regarding detailed information.
NG 4-10.5 inches WC
LP: 8–13 inches WC (Gas Models only)
27" (W) X 30" (D) X 3811/16" (H), 51" (D with door open)
68.6 cm (W) X 76.1 cm (D) X 98.3 cm (H), 129.7 cm (D with door open)
136 lbs (62 kg)
IEC 7.4 cu.ft. (22.5 lb/10.2 kg)
IEC 7.4 cu.ft. (8 lb/3.6 kg)
• Unplug dryer and call for service.
• Small loads of 1 to 5 items work best.
• Load fewer garments. Load similar-type garments.
• Use an iron to make creases.
• Depends on individual moisture level in skin.
• Select load weight manually before starting REDUCE STATIC option.
• Select the correct number or garments or load size before starting the cycle.
• Condensation will normally form on the inside of the dryer door during steam
operation. Some condensation may drip out the bottom of the door.
• Steam vapor is difficult to see when the door is closed. However, condensation
will normally form on the inside of the dryer door if the steam system is
operating normally.
• The drum is turned off so that the steam vapor remains in the drum. The drum
will normally turn for about 2 seconds once a minute.
• Steam is released at different stages of the cycle for each option.
• This display indicates that the steam option has been set for a "
as a comforter.
Press the LESS TIME button to reduce the indicated load size.
• Fabrics containing strong odors should be washed in a normal cycle.
• Pause the drying cycle and clean the lint filter.
• Install a shorter or straighter duct run. See the Installation Instructions.
• Ductwork should be checked/cleaned soon.
Dryer can be used in this condition, but drying times may be longer.
• If exhaust restrictions are sensed by the FLOW SENSE
will remain on for two hours after the end of the cycle. Opening the door or
pressing the POWER button will turn off the display.
Solutions
TM
system, the indicator
" item such
Publicité
