DeWalt DWE6411 Traduction De La Notice D'instructions Originale page 21

penetrate the paper, as shown in Figure G. (Press the punch into
the pad as far as it will go.) Remove the paper punch and the
paper is ready.
An alternate method of perforating the paper is to securely
fasten the punch to a suitable work surface. Two holes are
provided in the punch for this purpose. Use #8 flat head screws.
Press the sander (with the paper attached) down on the punch.
Dust Extraction (Fig. A, H)

WARNING: Since woodworking with a sander produces
dust, always install a dustbag designed in compliance
with the applicable directives regarding dust emission.
WARNING: Do not use a dustbag or vacuum extractor
without proper spark protection when sanding metal.
The tool is supplied with an adapter for connecting a dustbag or
a vacuum extractor.
Your sander has a built-in vac-adapter
the supplied dust bag or a shop vacuum system to be
10
connected. The built-in outlet utilizes the D
connection making it compatible with the D
extractor.
To Attach the Dust Bag
1. While holding the sander, fit the dust bag collar
vac-adapter 9 as shown in Figure H.
2. Turn the collar clockwise to lock the dust bag
11
place.
To Empty the Dust Bag
1. While holding the sander, turn the collar
to unlock the dust bag
2. Remove dust bag from the sander and gently shake or tap
the dust bag to empty.
3. Reattach the dust bag back onto the outlet and lock into
place by turning the dust bag collar clockwise.
You may notice that all the dust will not come free from the
bag. This will not affect sanding performance but will reduce
the sander's dust collection efficiency. To restore your sander's
dust collection efficiency, depress the spring inside the dust bag
when you are emptying it and tap it on the side of the trash can
or dust receptacle.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.

WARNING: .
• Make sure all materials to be sanded are well secured.
• Apply only a gentle pressure to the workpiece.
Excessive pressure does not improve the sanding
9 which allows either
WALT AirLock
e
WALT dust
e
11
10
11 anticlockwise
10 .
effect, but only results in an increased load on the
machine and causes the abrasive to tear.
• Avoid overloading.
WARNING: Do not sand magnesium!
Proper Hand Position (Fig. IA, IB)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main handle or
on the top of the unit as shown in Figures IA and IB.
Switching On and Off (Fig. A)
To switch the tool on, set the on/off switch
To switch the tool off, set the on/off switch to position O.
Sanding
1. Start with the coarsest grit size.
2. As the tool produces small scratch marks in all directions, it
is not necessary to sand with the grain.
to the
3. Check your work at short intervals.
4. Always switch off the tool when work is finished and before
in
unplugging.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
EngLIsh
to position I.
1
19