Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

XFL3/4/5/6-LED
INSTALLATION INSTRUCTIONS
ELECTRICAL SHOCK HAZARD
WARNING
Disconnect the Electrical supply power at the service panel (fuse or circuit breaker box). Failure to do so could result in serious
injury or death. Only qualified electricians should install this fixture and the installation MUST conform to the Canadian
Electrical Code Part I and all local codes and ordinances. Ensure that only proper tools, materials, and equipment are used to
complete the installation.
SAFETY
Proper grounding is required to ensure personal safety.
Fixture should be mounted in locations where unauthorized personnel will not readily subject it to tampering.
Do not use this equipment for anything other than its intended purpose.
Servicing this equipment should be performed by qualified service personnel.
Save these instructions.
MIN 75 °C SUPPLY CONDUCTOR
INSTALLATION
Slip Fitter:
1. Slip Fitter is installed as standard on this fixture. [1]
2. Loosen the adjusting bolt, align the fixture to required angle.
Tighten adjusting bolt after the angle is confirmed.
Note: Adjustable angle is 180°.
Yoke:
1. Remove slip fitter bracket and mounting screws on the fixture as shown. [2][3]
2. Install the yoke on the fixture as shown. [4][5][6]
3. Make the wiring connections as per diagram below. Install the
yoke onto chosen mounting location.
4. Loosen the adjusting bolts, align the fixture to required angle.
Tighten adjusting bolts after the angle is confirmed.[7][8]
Note: Adjustable angle is 180°.
[4]
RAB Design Lighting inc.
READ, UNDERSTAND
before installing the equipment.
[5]
August– 2024
FOLLOW
, and
these instructions
[1]
[2]
[6]
Adjusting
bolt
[3]
Page 1 of 6

Publicité

loading

Sommaire des Matières pour RAB Design XFL3-LED

  • Page 1 3. Make the wiring connections as per diagram below. Install the yoke onto chosen mounting location. 4. Loosen the adjusting bolts, align the fixture to required angle. Tighten adjusting bolts after the angle is confirmed.[7][8] Note: Adjustable angle is 180°. RAB Design Lighting inc. August– 2024 Page 1 of 6...
  • Page 2 XFL. Note: XFL3/4 uses DC Photocell, located behind the screw cap, while XFL5/6 uses AC Photocell. CCT & CCT & Watt CCT & Watt Watt Watt XFL3 XFL4 XFL5 RAB Design Lighting inc. August– 2024 Page 2 of 6...
  • Page 3 Connect fixture BLACK wire to power supply LINE wire. • • The fixture includes 0-10V dimming functionality, connect DIM- (pink) and DIM+ DIM- PINK (violet) wires to a 0-10V dimming controller (optional). DIM+ RAB Design Lighting inc. August– 2024 Page 3 of 6...
  • Page 4 Installer l'étrier sur l'emplacement de montage prévu. 4. Desserrez les boulons de réglage, alignez le projecteur à l'angle requis. Resserrer les une fois l'angle obtenu.[7][8] Note: L'angle de réglage est de 180°. RAB Design Lighting inc. August– 2024 Page 4 of 6...
  • Page 5 Remarque : XFL3/4 utilise une cellule photoélectrique DC, située derrière le bouchon à vis, tandis que XFL5/6 utilise une cellule photoélectrique AC. CCT & CCT & LUMEN CCT & LUMEN LUMEN LUMEN XFL3 XFL4 XFL5 RAB Design Lighting inc. August– 2024 Page 5 of 6...
  • Page 6 Connectez le fil NOIR du luminaire au fil LIGNE de l'alimentation. • • Le luminaire inclut une fonction de gradation 0-10V, connectez les fils DIM- (rose) et DIM+ (violet) à un gradateur 0-10V (en option). RAB Design Lighting inc. August– 2024 Page 6 of 6...

Ce manuel est également adapté pour:

Xfl4-ledXfl5-ledXfl6-led