Publicité
Quick Install Guide: PoLRE24/PoLRE48
System Grounding (Earthing)
The NVT Phybridge Technical Support Group is available to assist you with product installation, configuration, monitoring and troubleshooting
procedures. Should you experience trouble with this equipment or for repair or warranty information, please contact NVT Phybridge Inc. at
+1 905.901.3633 or support@nvtphybridge.com.
Technical Specifications
Model
Part Numbers
802.1x Support
Dimensions
Weight
Mounting
Processor
Memory
Interface: Ethernet Uplink (Trunk IP)
Interface: Downlink (PoE and IP to Adapter)
Management
Power Supply
Power Consumption
Power Injection (PoE)
PowerWISE
®
Power Sharing
Operating Temperature
Humidity
Specifications subject to change without notice.
Model
Part Number
802.1x Support
Dimensions
Weight
Interface: Ethernet Uplink (Trunk IP)
Interface: Downlink (PoE and IP to adapter)
Power Consumption
Power Injection (PoE)
Operating Temperature
Humidity
Specifications subject to change without notice.
888.901.3633 | +44 (0) 208 977 6614 |
PoLRE24/48
NV-PL-024 & NV-PL-048
Supported
19 inches x 1U Without rack ears: 9.92" x 17.13" x 1.75" (LxWxH)
25.2cm x 43.5cm x 4.45cm (LxWxH)
7.94lb (3.6kg)
Standalone or rack or shelf-mountable
2 brackets included for installation
Broadcom BCM56018 switch processor, 266MHz
32MB FLASH, 64MB DDR SDRAM
Maximum 2 uplinks, each 1Gb/s (full duplex), either:
•
2 mini-GBIC ports: 1000 Base-TX/SX/LX/EX/ZX/LHX (determined by SFP, transceiver
module installed), Ethernet IEEE 802.3z, fiber optic cable, or
•
2 RJ45 ports: 10/100/1000 Base-T autosensing, independent speed selection,
Ethernet IEEE 802.3, CAT5e copper cable
PL-024: 1 RJ21 male telco connector (standard), 24 pairs used
PL-048: 2 RJ21 male telco connectors (standard), 48 pairs used
Maximum Distance: 1200ft (365m) over CAT3 UTP cable, 24 AWG
Speed: 10 Mbps (full duplex)
Power: 1 Watts
1 LAN port (MGMT): RJ45 10/100 base-T autosensing, IEEE 802.3
1 UART console port: RJ45 to DB9 cable
Unit auto-sensing 100-240VAC, 50/60 Hz
Power output: 500W max at 100VAC, 1000W max at 240VAC
PL-024: 16.5W
PL-048: 22W
DC Voltage: -54VDC; Endpoint devices must be compliant with IEEE 802.3af
2 male connectors (rear), DC IN and DC OUT: 48VDC to 56VDC
14°F to 122°F (-10°C to +50°C)
10% to 95% (non-condensing) at 35° C
PhyLink
NV-PLLK-6 (Sold as 6 pack)
Supported
2.56" x 1.1" x 0.71" (LxWxH)
6.5cm x 2.8cm x 1.8cm (LxWxH)
0.78oz (22g)
1 RJ11 port: CAT3 unshielded single twisted pair cable. Between the wall plate and
adapter, you can reuse the existing silver satin when doing a DNIC/POTS displacement.
BT wall plate connectors may required optional BT Adapter Cables.
1 RJ45 port: 10/100 Base-T autosensing, IEEE 802.3af
10 Mb connection to IP end device
0.9W
58VDC
Endpoint devices must be compliant with IEEE 802.3af
32°F to 104°F (0°C to +40°C)
10% to 95% (non-condensing) at 35° C
www.nvtphybridge.com
Copyright 2024 NVT Phybridge | 413-0002-F |
Page
| 7
Publicité
