Publicité
Quick Install Guide: PoLRE24/PoLRE48
Configuring the PoLRE (2 Methods)
Default IP Address:
•
MGMT = 192.168.1.1
•
GBE1 &GBE2 = 192.168.100.1
Default Username & Password:
•
Username: admin
•
Password: admin
Accessibility:
•
Console cable connected
directly to the console port.
Console Port Serial Settings:
•
115200/8/N/1
Default Username & Password:
•
Username: admin
•
Password: admin
Changing Management Port Default IP Address
The Mgmt IP default address of 192.168.1.1 may conflict with other PoLRE devices. To avoid this from happening, you must change the IP
address of the Mgmt Port to an IP which will never be used on the network. For example, if your network belongs to the "192.168.X.X" subnet,
change the Mgmt Port IP to "10.10.1.1".
Steps to Change the Management Port IP Address:
1.
Log into the unit via the serial console port (115200,8,N,1,None).
2.
Type in "pal-set-sys-ip mgmt 10.10.1.1 255.255.255.0 10.10.1.255"
Substitute the provided example IP information for your own.
a. The usage is: pal-set-sys-ip mgmt <IPADDRESS> <NETMASK> <BROADCAST>
3.
You will be prompted to confirm this information.
4.
Refer to the CLI section of the administration guide for more information.
888.901.3633 | +44 (0) 208 977 6614 |
Connecting to the Admin GUI
Connecting to PoLRE:
1.
Change the IP address of your PC or
Laptop to 192.168.100.2
2.
Connect your Ethernet port on the PC or
Laptop to the GBE1 port on the PoLRE.
3.
Open a web browser (Chrome only) and
type in/go to http://192.168.100.1
4.
Login is "admin" password is "admin"
(without quotes)
5.
You are now in the Admin GUI.
NOTE: Change IP addresses to avoid
conflict. (Ethernet/Uplink Ports)
Connecting to the Command Line Interface (CLI)
Connect to the Console Port:
1.
Connect the RJ45 end of the serial cable to
the console port of the PoLRE. Connect the
serial end of the serial cable to the serial port
of your PC.
2.
Configure your serial port to 115200/8/N/1.
3.
Login is "admin", password is "admin"
(without quotes)
4.
4. You are now connected to the CLI via the
console port.
www.nvtphybridge.com
Connecting to PoLRE:
1.
Click on Ethernet menu option on the top
bar.
2.
Once Ethernet page is displayed select
UPLINK PORTS.
3.
Type in new IP address in the IP Address
section for in-band IP configuration.
4.
Type in new Net Mask in the Net Mask
section (e.g. 255.255.255.0).
5.
Type in new IP address of the system default
gateway in the Default Gateway section.
6.
Click Save Changes button to apply the
modifications.
7.
Refer to admin guide for more software
details.
Steps to Change the IP Address:
1.
Type in "pal-set-sys-ip GbE 192.168.9.1
255.255.255.0 192.168.9.255" Substitute the
provided example IP information for your
own.
a. The usage is: pal-set-sys-ip GbE
<IPADDRESS> <NETMASK> <BROADCAST>
2.
You will be prompted to confirm this
information.
3.
Refer to the CLI section of the administration
guide for more information.
Copyright 2024 NVT Phybridge | 413-0002-F |
Page
| 3
Publicité
