Publicité
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is applied.
5. Before starting the equipment
The lawn mower is delivered partly assembled.
The push bar and the grass basket must be as-
sembled before using the lawn mower. Follow the
instructions step by step and refer to the pictures
when assembling.
Important! Required assembly parts (screws,
cable guides, etc.) or functional parts (e.g. plugs,
wrenches, etc.) can be found in the molded parts
of the packaging or on the equipment.
Fitting the push bar (Fig. 3-4a)
Draw the push bar apart. Lock the two bottom
shafts (10/11) in position using the supplied
quick-release lever (12) as shown in Fig. 3. Take
care with the teeth on the handlebar adjustment
facility when you do so (A). If necessary, turn each
of the quick-release levers (12) back suffi ciently
on the thread so that it can still be fl ipped down
towards the back afterwards.
Next, lock the top push bar (2) with the two other
quick-release levers (12). If necessary, turn back
the quick-tightening screw suffi ciently on the
thread so that the quick-release lever (Fig. 3/Item
12) can then be fl ipped to the rear.
You can adjust the angle of the handlebar as a
whole to 3 diff erent settings (Fig. 4a) by fl ipping
up the two quick-release levers (Item 12). Only
these three positions are available. As you do this,
make sure that both sides are set to the same
position. To secure the push bar again, fl ip the two
quick-release levers back into the closed position.
You can adjust the angle of the long handle as a
whole by fl ipping up the two quick-release levers
(Item 12), with three settings available for the ang-
le (Fig. 4a). Only these three positions are availa-
ble. As you do this, make sure that both sides are
set to the same position. To secure the push bar
again, fl ip the two quick-release levers back into
the closed position.
You can adjust the angle of the upper push bar
(Fig. 4a) by fl ipping up the two upper quick-
release levers (Fig. 6/Item 12), with three settings
Anl_RASARRO_18-330_BL_SPK13.indb 21
Anl_RASARRO_18-330_BL_SPK13.indb 21
GB
available for the angle. As you do this, make sure
that both sides are set to the same position. To
secure the push bar again, fl ip the two quick-
release levers back into the closed position.
Then fasten the power cable to the upper push
bar and the lower right push bar with the cable
clips (Fig. 4/Item 14).
Fitting the catch basket
Before you fi t the catch basket you must ensure
that the motor is switched off and the blade is not
rotating. Ejector fl ap (Item 6) with one hand. Using
the other hand, grab onto the basket by the hand-
le and hang it in from the top.
Filling level indicator of the grass collector
The grass collector is equipped with a fi lling level
indicator (Fig. 5a/Item 15). which is opened by the
airfl ow that the lawn mower generates during ope-
ration. If the fl ap closes during mowing, the grass
collecting device is full and must be emptied. To
ensure the proper functioning of the fi lling level
indicator, the holes under the fl ap must always be
kept clean and passable.
Adjusting the cutting height
Caution!
Adjust the cutting height only when the machine
has been switched off and the safety plug has
been pulled out.
The cutting height is adjusted as follows
(see Fig. 6):
1. Push the lever (5) downwards.
2. Set the lever (5) to the desired cutting height.
3. Release the lever (5) and check that it is se-
curely seated in the lock.
Reading off the cutting height
The cutting height can be set between 25-65 mm
in 5 intervals, and can be read off on the scale.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged. To prevent any imbalance, replace
blunt and/or damaged blades. To carry out this
check, fi rst switch off the motor and pull out the
safety plug.
Charging the battery (Fig. 7)
1. Take the battery pack out of the equipment.
To do so, press the pushlock button (Fig. 8/
Item C).
2. Check that your mains voltage is the same as
- 21 -
13.04.2023 09:38:38
13.04.2023 09:38:38
Publicité
