Operation; Cleaning, Maintenance And Ordering Of Spare Parts; Replacing The Cutting Blade; Disposal And Recycling - EINHELL GE-LE 18/190 Li Instructions D'origine

All LEDs fl ash:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.

6. Operation

To obtain maximum performance from your lawn
edge trimmer, please follow the instructions given
below
•
Never use the lawn edge trimmer without the
guard.
•
Do not use the equipment when it is wet. The
best results are achieved with dry grass.
•
Set the lawn edge trimmer down on the rear
wheel for height adjustment (16) and tilt the
lawn edge trimmer just enough for starting it
up (Fig. 9).
•
To switch on your lawn edge trimmer, press
the safety lock-off (Fig. 6 / Item 3) and the On/
Off switch (Fig. 6 / Item 4).
•
To turn the lawn edge trimmer off, release the
On/Off switch (Fig. 6 / Item 4).
•
Do not allow the lawn edge trimmer near the
grass until the switch is pressed, i.e. the lawn
edge trimmer is in operation.
•
To avoid unnecessary wear, keep the lawn
edge trimmer away from hard objects.
•
Using a brush or similar, carefully remove all
residual grass from the guard hood at regular
intervals.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Before putting away or cleaning the grass trim-
mer, switch off and remove the battery pack.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
Anl_GE-LE_18-190_Li_SPK9.indb 20 Anl_GE-LE_18-190_Li_SPK9.indb 20
GB
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
•
Use a brush to remove deposits from the
safety guard

7.2 Replacing the cutting blade

Danger! Remove the battery!
Caution! Wear work gloves! Only replace the
cutting blade with a genuine Einhell replacement
cutting blade, as this will ensure top performance
and safety under all conditions.
Carry out the following steps to change the cut-
ting blade:
1. Insert the fi xing pin (17) in hole (A) provided
on the blade mount (see Fig. 10).
2. Undo the fastening screw using the wrench
(18) (see Fig. 11).
3. Remove the cutting blade and replace with a
new one.
4. When fi tting the cutting blade, make sure it is
installed in the right direction.
5. Then retighten the fastening screw with the
universal wrench (18).
7.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
Spare cutting blade Art. No.: 34.051.01

8. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
- 20 -
27.08.2020 16:08:59 27.08.2020 16:08:59